Page 2
I N T R O D U C T I O N The GEM-RP3DGTL is a “smart”, in- You'll probably find subjects men- gineered to the highest industry stan- tioned in this booklet that do not dards. To assure optimum safety and teractive, menu-driven keypad de- signed for your Napco control panel.
___ NO PROGRAMMING....................24 KEYPAD PANIC ENABLED?: ___ YES ___ NO KEYPAD MESSAGES ..................24 KEYPAD AUX. ENABLED?: GLOSSARY ....................26 ___ YES ___ NO SYSTEM TROUBLE ERROR CODES ............29 *FIRE HAS PRIORITY OVER BURGLARY. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 3...
Page 4
K E Y P A D C O N T R O L S & I N D I C A T O R S GEMINI SYSTEM ARMED SYSTEM ARMED ENT A1 ENT A1 01/01/97 01/01/97 12:00AM 12:00AM INTERIOR BYPASS FIRE/TBL SYS TBL CHIME NEXT/YES PRIOR/NO AREA COMPUTERIZED SECURITY SYSTEM GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 4...
YES ( ) button. (PRIOR). (3) Answers “NO” to ques- tions in the window display. BYPASS Button. (1) Deactivates se- lected zones from the system. (2) Un- bypasses a bypassed zone. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 5...
A 3-second beep will sound at the panel to indicate arming with a Priority Zone in trouble. Be sure to have the trouble repaired as soon as possible. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 6...
Page 7
Note: If a system trouble is indicated, the system cannot be armed using this method. To disarm all areas, press enter your code and press the button. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 7...
To cancel the entry delay while on the premises, merely press the button. (it may be pressed either before or after arming.) Note: While armed, the red ARMED light will flicker rapidly to indicate instant protection. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 8...
Page 9
Auxiliary Emergency. Simultaneously press the buttons to alert the central station of some other emergency. Police Emergency. Simultaneously press the buttons to alert the central station of a police emergency. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 9...
1. Enter your code and press the button. After the system is disarmed, the window will continue to display the number(s) of the zone(s) violated. 2. To reset the display, note the zones violated, then press the button. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 10...
Page 11
Alarm Event Log. If an audible output is programmed, a 24-Hour Zone will behave as an armed Burglary Zone. If the system is subsequently armed with a 24-Hour Zone in trouble, the keypad sounder will come on momentarily to indicate that there is a problem on the zone. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 11...
“FIRE TBL” (fire trouble) light, a flashing “SYS TBL” light and the sounder will BYPASS FIRE/TBL SYS TBL CHIME INTERIOR pulse to signal a malfunction. 2. Press the button to silence the sounder. Call for service immediately! GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 12...
Page 13
Would You Like More Safety Information? For more information on home fire detection, burn safety, and home fire safety, write to the National Fire Protection Association, Public Affairs Dept. 05A, Batterymarch Plaza, Quincy, MA 02269. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 13...
Page 14
F I R E P R O T E C T I O N Floorplan Draw a plan of your premises in the space provided below. Floorplan GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 14...
Page 15
(b) they may not nents could fail at any time. sense a fire on a different level of the residence GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 15...
SYS TBL CHIME INTERIOR 3. Activate Bell Test? Activates the alarm (while disarmed) for about 2 seconds. If INTERIOR BYPASS FIRE/TBL SYS TBL CHIME the alarm does not sound, call for service. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 16...
Page 17
This optional feature simultaneously turns on all zones designated as Day Zones. To deactivate the Watch Mode, arm, then disarm. All Day Zones will revert to regular Burglary Zones. Note: The Watch Mode is disabled while armed. BYPASS FIRE/TBL SYS TBL CHIME INTERIOR GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 17...
Page 18
12. Activate Fault Find? For installer's use only. If accidentally enabled, press the button to exit. BYPASS FIRE/TBL SYS TBL CHIME INTERIOR 13. Activate Locate? For installer's use only. If accidentally enabled, press the button to exit. BYPASS FIRE/TBL SYS TBL CHIME INTERIOR GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 18...
Page 19
15-minute countdown with the sounder pulsing. During this time, arming may be delayed an additional 1 to 4 hours (as above), or autoarming may be cancelled by arming and disarming the panel. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 19...
Page 20
NEXT to proceed to the next group, or PRIOR to scroll back to the previous group. Press the INTERIOR BYPASS FIRE/TBL SYS TBL CHIME button when done. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 20...
Opening and/or Closing Report- ing. Your system can notify the central station every time it is disarmed or GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 21...
Page 22
1. Enter a code valid for bypass, then press the button. 2. Press the button then the zone number (or vice versa) to deactivate that zone. Similarly, a bypassed zone may be unbypassed using the foregoing procedure. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 22...
If re-entry occurs during that 60 seconds, exit delay will restart once again (and only once again) at 60 seconds. If so programmed, re-entry within 60 seconds after exit delay has expired, will cause the alarm to sound a 2-second warning (in addition to the entry sounder) to remind the user to disarm. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 23...
While in the Program Mode, the The User Program Mode is accessed ARMED and STATUS lights remain from the Function Mode as follows: off and burglar and fire alarm func- 1. Enter your code, then press the GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 24...
Page 25
4 digits (for installer's use), then “UP” (indicating user programming) and the lights will continue to flash. 2. Press the button then to enter User No. 3, then press the button again followed by 3784 G0 G0 to program the code. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 25...
BYPASS Button - Enables you to Directory - A listing of the pro- GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 26...
Page 27
Ringback). status of the system (alarm, trouble, System Trouble - A problem (low low battery, etc.). battery, power failure, etc.) detected RF Low Battery - (Wireless sys in the system. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 27...
Page 28
Priority Zone: A zone that pre- vents arming if in trouble. Priority Zone with Bypass: A Pri- ority Zone that can be bypassed using the button. GEM-RP3DGTL.pub Wednesday, August 18, 1999 14:03 page 28...