Keypad Sounder On Alarm Zones; Auto Bypass Re-Entry Zones; Enable No Eolr Zones; Enable Telco Line Fault Test - Gemini GEM-P9600 Programming Instructions Manual

!
Page 16
16
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
H
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
17
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
H
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
18
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Press YES or NO)
19
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Press YES or NO)
20
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Press YES or NO)
21
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Press YES or NO)
22
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
H
_
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
23
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
H
_
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
X
GEM-P9600 Programming Instructions

Keypad Sounder On Alarm Zones

•
Enter the zone numbers of all zones to activate the Keypad Sounder upon alarm.
•
Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.
• U
Press to save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

Auto Bypass Re-entry Zones

•
Enter the zone numbers of zones to be Auto Bypass Re-entry zones.
•
Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.
• U
Press to save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.
•
Auto Bypass Re-entry Zones allow the system to be armed with the zone faulted but come back into the system
(armed) when the zone is subsequently closed.
Enable No EOLR Zones (New Program Only)
•
Press YES to program all zones except 24 Hr & fire zones for No End Of Line Resistor. Press NO to continue.
•
Do not program this feature for UL Installations.

Enable Telco Line Fault Test?

•
Press YES to enable Telco Line Fault Test.
•
Press NO to continue. NOTE: If enabled, a Telco Line Fault Test Delay of 60 sec. will automatically be pro-
grammed.

Enable Burg Output Chirp on KeyFob?

•
Press the NEXT/YES button to enable Burg Output Chirp on KeyFob Arm / Disarm.
•
Press the PRIOR/NO button to continue.
NOTE: The Burg Output will chirp once on Keyfob Arm and twice on Keyfob Disarm.

Enable SIA CP-01 Features?

•
Press the NEXT/YES button to enable.
•
Press the PRIOR/NO button to continue.
The SIA CP-01 Features are designed to reduce the incidence of false alarms. NOTE: Do not enable unless
reporting, otherwise system trouble Fail to Communicate may occur.

Number of Keypads in Area 1

•
Enter the total number of Keypads to be installed in Area 1.
•
Valid entries are from 01 to 15. Directly enter the number of keypads, including leading zeros.
U
Press to save. Press the NEXT/YES button to proceed.

Number of Keypads in Area 2

•
Enter the total number of Keypads to be installed in Area 2.
•
Valid entries are from 01 to 15. Directly enter the number of keypads, including leading zeros.
U
Press to save. Press the NEXT/YES button to proceed.
(New Program Only)
(Not evaluated by UL)
(New Program Only)
L
WI 1185 6/03
NAPCO Security Systems