Enter User Codes - Gemini GEM-P9600 Programming Instructions Manual

!
Page 18
27
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
Valid entries are: 0-9. Note: Press the
boxes. If an "Ambush Code" (Address 0495) is entered, do not program the first two digits of ANY User Code as the
same digits entered for the "Ambush Code".
!
If the programmed code is less than 6 digits, press the
!
Refer to the tables below for the available User Option and User Level data entries. Enter the user options data in
the left digit. Enter the level data (with arming options, if any, added) in the right digit. Note: For entries greater than 9,
press the buttons through the
G1
!
For Keypad Access Control, press the
below, use the number buttons to enter the data for Keypad 1–4 in the right digit; and the data for Keypad 5–8 data in
the left digit. (Press the
0
Example: Enter a code of "123456" as
"123456" (from left to right).
USER OPTIONS
DATA BLOCKED USER BYPASS
ENTRIES VIEW PROGRAM
blank (•) DISABLED
1 Y
2 Y
3 Y Y
4 Y
5 Y Y
6 Y Y
7 Y Y Y
8
9 Y
0 Y
B Y Y
C Y
D Y Y
E Y Y
F Y Y Y
Note: "Y" indicates option is enabled.
X
GEM-P9600 Programming Instructions
Enter User Codes (Press the
Enter up to 96 User Codes with User Options, Authority Level and Access Control
Options (if necessary) for each code. Refer to the tables below and on the next page
for available data entries for User Options, Authority Level and Access Control
Options. Note: All 96 Users must be assigned to areas in "Enable User Code by
Area" (Address 2500-2595) in Direct Address Programming. By default, only User 1
is enabled in Area 1 and Area 2.
User 2 - 8 are enabled in Area 1 and user 9 - 16 are enabled in Area 2.
!
Press the
R
buttons through
1
(4 digits is recommended) in the first six boxes from left to right for each user code.
button for a zero. No blank spaces in between; leave blank (•) any trailing
0
G5
button once again to program applicable keypads. Refer to the tables
R
buttons for blank).
USER OPTIONS
USER CODE
(UP TO 6 DIGITS)
DATA AUTHORITY
ENTRIES LEVEL
OVERVIEW
blank (•) NONE ARM/DISARM
1 LEVEL 1 ARM/DISARM
2 LEVEL 2 ARM/DISARM
3 LEVEL 3 ARM/DISARM
4 NONE
5 LEVEL 1
6 LEVEL 2
7 LEVEL 3
8 NONE
Y 9 LEVEL 1
Y 0 LEVEL 2
Y B LEVEL 3
Y
Y
Y
Y
Y
button to set cursor.)
R
button to set the cursor to the User Code. Use the number
to enter a code from 3 to 6 digits. Enter up to 6 digits
9
button to set the cursor to the OPTION/LEVEL.
R
buttons for B through F, respectively.
USER USER ACCESS CONTROL
OPTION LEVEL KEYPADS
CODE ACCESS CONTROL KEYPADS
TYPE
DATA K.P. 5 K.P. 6 K.P. 7 K.P. 8
ENTRIES
blank (•) NONE
1 Y
2 Y
ARM ONLY
3 Y Y
ARM ONLY
4
ARM ONLY
5 Y
ARM ONLY
6 Y
SERVICE
7 Y Y
SERVICE
8
SERVICE
9 Y
SERVICE
0 Y
B Y Y
C
D Y
E Y
F Y Y
Note: "Y" indicates option is enabled.
WI 1185 6/03
ACCESS CONTROL KEYPADS
DATA K.P. 1 K.P. 2 K.P. 3 K.P. 4
ENTRIES
blank (•) NONE
1 Y
2 Y
3 Y Y
Y 4
Y 5 Y
Y 6 Y
Y 7 Y Y
Y 8
Y 9 Y
Y 0 Y
Y B Y Y
Y Y C
Y Y D Y
Y Y E Y
Y Y F Y Y
Note: "Y" indicates option is enabled.
L
NAPCO Security Systems
Y
Y
Y
Y
Y
Y
Y
Y
Y Y
Y Y
Y Y
Y Y