Rf Transmitter Points; Quick Method; Key Fob Transmitters (As Arm/Disarm & Control Devices) - Gemini GEM-P9600 Programming Instructions Manual

!
Page 12
Zn# 01
000000
(Direct Entry)
:0 Pt
(Direct Entry)
G5.
Z N # X M I T # + C S P
Z n 0 1 - 0 0 0 0 0 0 : 0 - 0
Z N # X M I T # + C S P
Z N 0 1 - E N R O L L : A - -
Example. A 2-point transmitter has the RF ID number 287613:1. Map point
1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone "06".
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that one point
has been programmed. (Transmitter 287613:1, point 1 will be mapped
KEY FOB ZONE ASSIGNMENT: Key fobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm
system, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the key
fob, the location where the person holding the key fob is stationed, or the special purpose of the key fob button being depressed.
See the next page on Key Fob Transmitters as Zone Input Devices .
KFob01
Area
(Direct Entry)
000000
(Direct Entry)
:0 0 0
(Direct Entry)
X
GEM-P9600 Programming Instructions
RF Transmitter Points (Press
For each transmitter enter: (For wireless systems only. Also see Quick Method, which follows)
•
The zone number (01–96) to which the transmitter will be mapped.
•
The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
•
The point number (1–2); enter "9" for unsupervised (all points).
U
•
Press to save and NEXT/YES button to proceed when all transmitters have been entered.
NOTE: When programming the ID Code number, "0" through "9" = 0 through 9; A = G0 ;
B = G1 ; C = G2 ; D = G3 ; E = G4 and "F" =

Quick Method.

If a receiver is already installed in the panel, transmitter wireless points can be pro-
grammed automatically ("enrolled") using the following procedure. NOTE: The transmitter point will be en-
rolled only if the signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be mapped.
2. Press B to enter the Enroll Mode. The red and green LEDs on the keypad will flash and the window will
display as shown at left.
3. Open the loop of the point that is to be programmed (GEM-TRANS2 only).
4. Install the transmitter battery. The keypad will beep to indicate that the point has been successfully enrolled.
Multi-point transmitters can be mapped to successive zones simultaneously.
Key Fob Transmitters as Arm/Disarm & Control Devices (Press
Key fobs can be programmed as "Arm/Disarm" devices using their On/Off buttons (refer to WI752). For each
Key Fob Transmitter, enter:
•
The Key Fob Transmitter number (01–16).
•
The area number to which transmitter is assigned (0 to disable keyfob, 1 or 2).
•
The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
•
The Aux 1 Option (see key fob aux 1 & aux 2 options).
•
The Aux 2 Option (see key fob aux 1 & aux 2 options).
U
•
Press to save and NEXT/YES button to proceed when all key fobs have been entered.
NOTE: When programming the ID Code number, "0" through "9" = 0 through 9 ; A = G0 ;
B = G1 ;
C = G2 ; D = G3 ; E = G4 and "F" = G5.
to set cursor.)
R
to Zone 6).
5. Enter Zone "09".
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad will beep
once to indicate that one point has been programmed. (Transmitter
287613:1, point 2 is mapped to Zone 9).
WI 1185 6/03
to set cursor).
R
L
NAPCO Security Systems