Summary of Contents for Backyard Discovery Montpelier 30211
Page 1
• Assembly Instructions • • Warranty Information • Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445 Register your new swing set on-line @ www.swingsetonline.com (you will also find any updates on assembly instructions and information to order replacement parts) Features the fastening system.
Page 2
STOP PARE Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.com ¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA! La tienda donde realizó...
Page 3
Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Page 4
Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2.
Page 5
Owner’s Manual Play Set The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth 6" (152mm) 9" (228mm) 12"...
Page 6
Owner’s Manual Play Set 15. Instruct children to never jump from a fort deck. They should always use the ladder, ramp or slide. 16. Instruct children to never crawl or walk across the top of monkey bars. 17. Instruct children to never crawl on top of a fort roof. 18.
Page 7
Third Party Assembly: Customer may, in their sole discretion, elect to use a third party person or service to assemble this product. Backyard Discovery assumes no responsibility or liability for any charge incurred by the Customer for any assembly services’.
Page 8
Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS X3.1 The U.S.
Page 9
The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3. What age range is appropriate for the playsets? Backyard Discovery playsets are recommended for children ages 3 –...
Page 10
11. The end beam is not straight up and down. Why not? This is normal. Backyard Discovery designs playsets this way to ensure the strongest structure possible. The slight angle adds strength and reduces rocking and twisting.
Page 11
Tools Required for Installation: (These are the tools that are generally required for assembly of our swing sets. These tools are not included in the swing set purchase.) (Open End Wrenches (Nut Drivers 1/2" & 9/16") (Level 24") 1/2" & 7/16") (3/8"...
Page 12
B B B B a a a a s s s s i i i i c c c c S S S S e e e e t t t t u u u u p p p p D D i i i i m m m m e e e e n n n n s s s s i i i i o o o o n n n n s s s s Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry...
Page 13
Parts Identification Wood Components (NOT TO SCALE) E1 - TOWER LEG - W101453 1 3/8"x3 3/8"x89 1/2" (36x86x2274) E2 - TOWER LEG - W101445 1 3/8"x3 3/8"x89 1/2" (36x86x2274) E3 - TOWER LEG - W101450 1 3/8"x3 3/8"x73 1/8" (36x86x1856) E4 - MONKEY BAR UPRIGHT - W101733 1 3/8"x3 3/8"x71 3/8"...
Page 14
Parts Identification Wood Components (NOT TO SCALE) H4 - TABLE SUPPORT - W100560 1"x2"x4" (24x51x102) H74 - LEFT UPRIGHT - W100608 1"x3 3/8"x50 3/4" (24x86x1290) H75 - RIGHT UPRIGHT - W100609 1"x3 3/8"x50 3/4" (24x86x1290) H76 - LADDER RUNG - W100611 1"x3 3/8"x18 1/8"...
Page 21
Parts Identification A A A A c c c c c c c c e e e e s s s s s s s s o o o o r r r r i i i i e e e e s s s s (NOT TO SCALE) EK - SLIDE RAIL 8' GREEN RIGHT (2) FR - LEAF HINGE...
Page 22
4 Ft Ladder Phase 1 & 2 Phase Notes DESCRIPTION LABEL LEFT UPRIGHT • Assemble with hardware as shown. • Center rungs in rail grooves. LADDER RUNG SCREW PFH 8x2 SCREW PFH 8x2 DESCRIPTION LABEL RIGHT UPRIGHT SCREW PFH 8x2 SCREW PFH 8x2...
Page 23
4 Ft Ladder Phase 3 Phase Notes • Assemble with hardware as shown. SCREW PFH 8x2 DESCRIPTION LABEL REAR SUPPORT SCREW PFH 8x2...
Page 24
4 Ft Monkey Bar Phase 1 Phase Notes • You will build a left and right top rail assembly in this phase. • After building left assembly as shown, repeat steps for right assembly. See below for oreintation of right side triangle plate. •...
Page 25
4 Ft Monkey Bar Phase 2 Phase Notes • Assemble with hardware as shown. • Repeat with other side. DESCRIPTION LABEL MONKEY BAR UPRIGHT T-NUT 5/16 BOLT WH 5/16x1-1/2 T-NUT 5/16 BOLT WH 5/16x1-1/2...
Page 26
4 Ft Monkey Bar Phase 3 Phase Notes • Assemble with hardware as shown. MONKEY BAR RUNG 559 SCREW TAPPING 14x1-1/2 DESCRIPTION SCREW TAPPING 14x1-1/2 MONKEY BAR RUNG 559...
Page 27
4 Ft Monkey Bar Phase 4 Phase Notes • Assemble with hardware as shown. DESCRIPTION LABEL BOLT HEX 5/16x2-3/4 T-NUT 5/16 WASHER FLAT 9x18 WASHER LOCK INT 8x15 BOLT WH 5/16x1-1/2 LAG SCREW WH 5/16x2 WASHER LOCK EXT 8x19 NUT BARREL WH 5/16x7/8 WASHER LOCK EXT 12x19 MONKEY BAR BRACE MONKEY BAR GROUND BOARD...
Page 28
4 Ft Monkey Bar Phase 5 Phase Notes • Assemble with hardware as shown. DESCRIPTION SCREW TAPPING 14x1-1/2 WASHER FLAT 9x18 WASHER LOCK INT 8x15 HAND GRIP YELLOW PLASTIC HAND GRIP YELLOW PLASTIC WASHER FLAT 9x18 WASHER LOCK INT 8x15 SCREW TAPPING 14x1-1/2...
Page 29
4 FT WAVE RUNNER SWING BEAM PHASE 1 Phase Notes • Assemble with hardware as shown. QTY. DESCRIPTION LABEL SWINGBEAM SUPPORT SB73 END SUPPORT BOLT WH 5/16x2-1/2 WASHER FLAT 8x27 WASHER FLAT 8x27 BOLT WH 5/16x1-3/4 NUT LOCK 5/16 L BRACKET 66x66x127 GREEN NUT LOCK 5/16 BOLT HEX 5/16x2-3/4 TRIANGLE PLATE 105 5 HOLE...
Page 32
8 FOOT SLIDE ASSEMBLY PHASE 1 Phase Notes ● DRILL 3 HOLES AT ONE END OF THE PLASTIC SLIDE BED USING A 5/16" DRILL BIT AND USING THE DIMENSIONS SHOWN BELOW. THIS END WILL BE THE TOP OF THE SLIDE. ●...
Page 33
8 FOOT SLIDE ASSEMBLY PHASE 2 Phase Notes ● PLACE 1 SLIDE RAIL ON A FLAT SURFACE AND BEGIN INSERTING SLIDE BED AT THE BOTTOM OF THE SLIDE RAIL. PUT SLIDE SUPPORT BOTTOM INTO THE SUPPORT POCKET AT THE BOTTOM OF THE RAIL AND HAVE A HELPER BEND THE SLIDE BED TOWARDS THE TOP OF THE SLIDE AND INSERT THE BED INTO THE SLIDE CAVITY.
Page 46
Fort Assembly Phase 8 Hardware needed: Parts needed: • (12) BR - SCREW PFH 8x1-1/8 - A100088 • (6) N4 - PICKET - W101492 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with Note: It is vital that the fort a 1/8"...
Page 49
Fort Assembly Phase 11 Hardware needed: Parts needed: • (33) BR - SCREW PFH 8x1-1/8 - H100088 • (11) M5 - WALL BOARD - W101497 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with Note: It is vital that the fort a 1/8"...
Page 50
Fort Assembly Phase 12 Hardware needed: Parts needed: • (36) BR - SCREW PFH 8x1-1/8 - H100088 • (9) M17 - WALL BOARD - W101493 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you Note: It is vital that the fort must pre-drill each board with be level before and after a 1/8"...
Page 51
Fort Assembly Phase 13 Hardware needed: Parts needed: • (46) BR - SCREW PFH 8x1-1/8 - H100088 • (2) M7 - WALL BOARD - W100579 • (9) M11 - WALL BOARD- W100583 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with a 1/8"...
Page 53
Fort Assembly Phase 15 Hardware needed: Parts needed: • (6) CK - SCREW PFH 8x2 - H100111 • (1) BAY WINDOW ASSEMBLY Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with Note: It is vital that the fort a 1/8"...
Page 54
Fort Assembly Phase 16 Hardware needed: Parts needed: • (37) BR - SCREW PFH 8x1-1/8 - H100088 • (1) L9 - DOOR BOARD - W101233 • (4) BC - SCREW PWH 8x3/4 - H100070 • (2) M19 - DOOR BOARD - W101230 •...
Page 60
Fort Assembly Phase 22 Parts needed: Hardware needed: • (2) GABLE END ASSEMBLY • (56) BP - SCREW PWH 8x1-1/2 - H100086 • (14) R1 - ROOF BOARD - W101503 Phase Notes • Assemble with hardware as shown. Step 1: Attach 'R1' Roof Board to the edge of Gable End Assembly using Screws 'BP', as shown.
Page 63
Fort Assembly Phase 25 Hardware needed: Parts needed: • (2) B - NUT BARREL 5/16x5/8 - H100004 • (1) BENCH ASSEMBLY • (2) AD - WASHER LOCK EXT 12x19 - H100031 • (2) CM - BOLT WH 5/16x1/2 - H100115 Phase Notes •...
Page 64
Ladder Attachment Phase 26 Hardware needed: Parts needed: • (2) Z - LAG SCREW WH 5/16x2 - H100027 • (1) LADDER ASSEMBLY • (2) AC - WASHER LOCK EXT 8x19 - H100030 Phase Notes • Assemble with hardware as shown. Step 1: Attach the Ladder Assembly to 'H1' Floor Rail using Lag Screws 'Z' and Washer 'AC', as shown.
Page 65
Monkey Bar Attachment Phase 27 Hardware needed: Parts needed: • (4) CM - BOLT WH 5/16x1/2 - H100115 • (1) MONKEY BAR ASSEMBLY Phase Notes • Assemble with hardware as shown. Step 1: Attach the Monkey Bar Assembly to 'L1' Wall Rail using Bolts 'CM' through the angle brackets into T-Nut 'BG', as shown.
Page 66
• (4) BX - WASHER SPLIT 5/16 - H100095 • (1) SWING BEAM ASSEMBLY • (4) CD - WASHER FLAT 8x27 - H100105 • (1) HC - BACKYARD DISCOVERY ID TAG - A100164 • (4) AJ - BOLT HEX 5/16x1-1/4 - H100042 • (1) WAVE RIDER ASSEMBLY •...
Page 68
Anchoring Instructions Phase 30 Hardware needed: Parts needed: • (6) KS - NUT BARREL 1/4x5/8 - H100136 • (6) KC - METAL GROUND STAKE BROWN - A100178 • (12) CE - WASHER FLAT 9x18 - H100106 • (2) DP - SWING SEAT GREEN - A100027 •...
Page 69
Limited Warranty. In addition, Backyard Discovery will replace any parts within the first 30 days from date of purchase found to be missing from or damaged in the original packaging.
Need help?
Do you have a question about the Montpelier 30211 and is the answer not in the manual?
Questions and answers