• Assembly Instructions • • Warranty Information • Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445 Register your new swing set on-line @ www.swingsetonline.com (you will also find any updates on assembly instructions and information to order replacement parts) Features the fastening system.
Page 2
STOP PARE Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.com ¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA! La tienda donde realizó...
Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2.
Owner’s Manual Play Set The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth 6" (152mm) 9" (228mm) 12"...
Owner’s Manual Play Set 15. Instruct children to never jump from a fort deck. They should always use the ladder, ramp or slide. 16. Instruct children to never crawl or walk across the top of monkey bars. 17. Instruct children to never crawl on top of a fort roof. 18.
Page 7
Third Party Assembly: Customer may, in their sole discretion, elect to use a third party person or service to assemble this product. Backyard Discovery assumes no responsibility or liability for any charge incurred by the Customer for any assembly services’.
Page 8
Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS X3.1 The U.S.
Page 9
The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3. What age range is appropriate for the playsets? Backyard Discovery playsets are recommended for children ages 3 –...
Page 10
11. The end beam is not straight up and down. Why not? This is normal. Backyard Discovery designs playsets this way to ensure the strongest structure possible. The slight angle adds strength and reduces rocking and twisting.
Tools Required for Installation: (These are the tools that are generally required for assembly of our swing sets. These tools are not included in the swing set purchase.) (Open End Wrenches (Nut Drivers 1/2" & 9/16") (Level 24") 1/2" & 7/16") (3/8"...
Page 12
B B B B a a a a s s s s i i i i c c c c S S S S e e e e t t t t u u u u p p p p D D i i i i m m m m e e e e n n n n s s s s i i i i o o o o n n n n s s s s Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires.
Page 22
Parts Identification Hardware LB - LAG SCREW WH 1/4x1 - H100144 (35) KS - NUT BARREL WH 1/4x5/8" - H100136 LC - LAG SCREW WH 1/4x1-1/2 - H100145 (80) AA - LAG SCREW WH 5/16x2-1/2 - H100028 (15) C - NUT BARREL WH 5/16x1-1/2 - H100006 (13) AB - LAG SCREW WH 5/16x3 - H100029 (19)
Page 23
Parts Identification A A A A c c c c c c c c e e e e s s s s s s s s o o o o r r r r i i i i e e e e s s s s (NOT TO SCALE) EJ - L BRACKET GREEN 54x67 -A100053...
Page 24
Parts Identification A A A A c c c c c c c c e e e e s s s s s s s s o o o o r r r r i i i i e e e e s s s s (NOT TO SCALE) DT - SLIDE RAIL10' TOP LEFT GREEN - A100032 DR - SLIDE RAIL 10' BOTTOM LEFT GREEN - A100030...
Page 25
Parts Identification A A A A c c c c c c c c e e e e s s s s s s s s o o o o r r r r i i i i e e e e s s s s (NOT TO SCALE) LH - BOUNCE TUBE BOTTOM GREEN -A100221...
Page 26
10 Foot Slide Assembly Phase 1 Phase Notes • Drill 3 holes at one end of the plastic slide bed using a 5/16" drill bit and using the dimensions shown below. This end will be the top of the slide. •...
Page 27
10 Foot Slide Assembly Phase 2 Phase Notes • Assemble with hardware as shown. • Repeat on other side, making a left and right assembly. QTY. DESCRIPTION LABEL SLIDE RAIL 10' BOTTOM LEFT GREEN SLIDE RAIL 10' BOTTOM RIGHT GREEN SLIDE RAIL 10' TOP LEFT GREEN SLIDE RAIL 10' TOP RIGHT GREEN BOLT WH 5/16x1/2...
Page 28
10 Foot Slide Assembly Phase 3 Phase Notes • You will need a helper from this point on. • Place 1 slide rail assembly on a flat surface and begin inserting slide bed at the bottom of the slide rail. Put slide support board into the support pocket at the bottom of the rail and have a helper bend the slide bed towards the top of the slide and insert the bed into the slide cavity.
Page 29
10 Foot Slide Assembly Phase 4 Phase Notes • Once bed, support tubes, and support board are completely in the cavity and in the support pocket, secure using 3" screws at each of the pilot hole locations as shown. QTY. DESCRIPTION LABEL SCREW PFH 8x3"...
Page 30
6 FT WAVE RUNNER SWING BEAM PHASE 1 Phase Notes • Assemble with hardware as shown. L BRACKET 66x66x127 GREEN WASHER FLAT 8x27 QTY. DESCRIPTION LABEL SWINGBEAM SUPPORT NUT LOCK 5/16 END SUPPORT SP71 BOLT WH 5/16x2-1/2 WASHER FLAT 8x27 NUT LOCK 5/16 BOLT HEX 5/16x4-1/4 TRIANGLE PLATE 105 5 HOLE...
Page 32
6 FT WAVE RUNNER SWING BEAM PHASE 3 Phase Notes • Assemble with hardware as shown. QTY. DESCRIPTION LABEL DUCTILE HANGER WASHER FLAT 11x25 WASHER LOCK INT 10x18 BOLT HEX 3/8x5-3/4 T-NUT 3/8 T-NUT 3/8 DUCTILE HANGER WASHER FLAT 11x25 WASHER LOCK INT 10x18 BOLT HEX 3/8x5-3/4...
Page 33
6 Ft Rock Wall Green Phase 1 Phase Notes • Assemble slats to rails as shown. • Note orientation of slats and arrange as shown. • Attach rock wall board (M74) first. See detail at bottom. • Using slats as a guide, pre-drill edges of rails with a 1/8"...
Page 34
6 Ft Rock Wall Green Phase 2 Phase Notes • Assemble middle support with screws as shown. See detail below. • Using slats as a guide, pre-drill edge of middle support with a 1/8" drill bit. Failure to pre-drill may result in board splitting. DESCRIPTION LABEL SCREW PFH 8x1-1/2...
Page 35
6 Ft Rock Wall Green Phase 3 Phase Notes • Assemble N7 to top of rails as shown. See detail below. • Using N7 as a guide, pre-drill top edge of rails with a 1/5" drill bit. Failure to pre-drill may result in board splitting.
Page 36
6 Ft Rock Wall Green Phase 4 Phase Notes • Assemble rocks to boards using hardware as shown. BOLT PTH 1/4X1 WASHER LOCK INT 8x15 T-NUT 1/4 CLIMBING ROCK - GREEN DESCRIPTION LABEL CLIMBING ROCK GREEN BOLT PTH 1/4x1 WASHER LOCK INT 8x15 T-NUT 1/4...
Page 37
5 Ft Ladder Phase 1 & 2 Phase Notes QTY. DESCRIPTION LABEL LEFT UPRIGHT • Assemble with hardware as shown. LADDER RUNG • Center rungs in rail grooves. SCREW PFH 8x2 SCREW PFH 8x2 SCREW PFH 8x2 QTY. DESCRIPTION LABEL RIGHT UPRIGHT SCREW PFH 8x2...
Page 38
5 Ft Ladder Phase 3 Phase Notes • Assemble with hardware as shown. SCREW PFH 8x2 LAG SCREW WH 1/4x1-1/2 HAND GRIP GREEN 816 c/c QTY. DESCRIPTION LABEL REAR SUPPORT SCREW PFH 8x2 HAND GRIP 816 C/C LAG SCREW WH 1/4x1-1/2...
Page 39
Bounce Tube Green & Yellow Phase 1 Hardware needed: Parts needed: • (6) KT - BOLT WH 1/4x1 - H100137 • (1) LG - BOUNCE TUBE TOP GREEN - A100213 • (6) KV - WASHER LOCK EXT 6x15 - H100138 •...
Page 48
Sound Module Kit * To replace batteries, remove (4) screws used to hold the battery cover. Lift battery cover away from module. Replace old batteries with new batteries. Place cover back on module and re-insert screws, as shown. * Do not mix old and new batteries. SCREW TAPPING 4x3/4 * Do not mix alkaline, standard or rechargeable batteries.
Page 49
Sound Module w/Bungee Bracket ROCK WALL SOUND MODULE KIT - A100187 (4) SCREW TAPPING 4x3/4 BUNGEE MOUNT BASE BUNGEE CORD 310 PQ - BUNGEE MOUNT -A100249-2 BUNGEE MOUNT PR - BUNGEE CORD 310 -A100250-2 * To replace batteries, remove (4) screws used to hold the battery cover.
Page 50
Fort Assembly Phase 1 Parts needed: Hardware needed: • (2) E1 - FORT UPRIGHT - W101609 • (6) BG - T-NUT 5/16 - H100074 • (1) E2 - FORT HANDLE UPRIGHT - W101613 • (18) AC - WASHER LOCK EXT 8x19 - H100030 •...
Page 57
Fort Assembly Phase 8 Hardware needed: Parts needed: • (24) BR - SCREW PFH 8x1-1/8 - H100088 • (6) M9 - PICKET - W101651 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with a 1/8"...
Page 59
Fort Assembly Phase 10 Parts needed: Hardware needed: • (2) O1 - WINDOW SLAT - W101688 • (4) BR - SCREW PFH 8x1-1/8 - H100088 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you Note: It is vital that the fort must pre-drill each board with be level before and after a 1/8"...
Page 60
Fort Assembly Phase 11 Hardware needed: Parts needed: • (10) AC - WASHER LOCK EXT8x19 - H100030 • (1) H2 - FLOOR SUPPORT BOARD - W101608 • (2) L - BOLT WH 5/16x2-1/4 - H100013 • (1) H3 - FLOOR JOIST - W101638 •...
Page 61
Fort Assembly Phase 12 Hardware needed: Parts needed: • (2) D - NUT BARREL WH 5/16x7/8 - H100005 • (2) E6 - DECK BRACE - W101666 • (2) AD - WASHER LOCK EXT12x19 - H100031 • (4) AC - WASHER LOCK EXT8x19 - H100030 Phase Notes •...
Page 62
Fort Assembly Phase 13 Parts needed: Hardware needed: • (69) BS - SCREW PFH 8x1-3/4 - H100089 • (2) L3 - OUTER FLOOR BOARD - W101637 • (11) M11 - FLOOR BOARD - W101635 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with Note: It is vital that the fort...
Page 64
Fort Assembly Phase 15 Hardware needed: Parts needed: • (2) D - NUT BARREL WH 5/16x7/8 - H100005 • (1) E10 - RIGHT HANDLE POST - W101644 • (2) AD - WASHER LOCK EXT12x19 - H100031 • (1) N2 - PICKET - W101647 •...
Page 65
Fort Assembly Phase 16 Hardware needed: Parts needed: • (16) BR - SCREW PFH 8x1-1/8 - H100088 • (4) M13 - PICKET - W101649 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you Note: It is vital that the fort must pre-drill each board with be level before and after a 1/8"...
Page 67
Fort Assembly Phase 18 Hardware needed: Parts needed: • (4) BR - SCREW PFH 8x1-1/8 - H100088 • (2) O1 - WINDOW SLAT - W101688 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you Note: It is vital that the fort must pre-drill each board with be level before and after a 1/8"...
Page 68
Fort Assembly Phase 19 Hardware needed: Parts needed: • (16) BR - SCREW PFH 8x1-1/8 - H100088 • (4) M13 - PICKET - W101649 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with Note: It is vital that the fort a 1/8"...
Page 70
Fort Assembly Phase 21 Hardware needed: Parts needed: • (8) BR - SCREW PFH 8x1-1/8 - H100088 • (2) O1 - WALL SLAT - W101688 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with a 1/8"...
Page 71
Fort Assembly Phase 22 Hardware needed: Parts needed: • (2) KS - NUT BARREL WH 1/4x5/8 - H100136 • (2) FX - HAND GRIP METAL GREEN 381 c/c - A100118 • (2) KW - WASHER LOCK EXT 8x15 - H100139 Phase Notes •...
Page 72
Fort Assembly Phase 23 Hardware needed: Parts needed: • (4) LB - LAG SCREW WH 1/4x1 - H100144 • (2) FX - HAND GRIP METAL GREEN 381 c/c - A100118 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board with a 1/8"...
Page 73
Fort Assembly Phase 24 Hardware needed: Parts needed: • (4) E - NUT BARREL WH 5/16x1-3/4 - H100007 • (2) H4 - SEAT BOARD - W101682 • (12) AD - WASHER LOCK EXT 12x19 - H100031 • (2) H8 - SEAT SUPPORT - W101581 •...
Page 74
Fort Assembly Phase 25 Hardware needed: Parts needed: • (4) E - NUT BARREL WH 5/16x1-3/4 - H100007 • (2) H11 - TABLE SUPPORT - W101683 • (6) AD - WASHER LOCK EXT 12x19 - H100031 • (2) H12 - PICNIC TABLE BRACE - W101686 •...
Page 79
• (1) SWING BEAM ASSEMBLY • (4) CD - WASHER FLAT 8x27 - H100105 • (1) HC - BACKYARD DISCOVERY ID TAG - A100164 • (4) AJ - BOLT HEX 5/16x1-1/4 - H100042 • (4) CY - SCREW PWH 8x3/4 - H100128 Phase Notes •...
Page 80
Rock Wall Attachment Phase 31 Hardware needed: Parts needed: • (3) AA - LAG SCREW WH 5/16x2-1/2 - H100028 • (1) ROCK WALL ASSEMBLY • (3) AC- WASHER LOCK EXT 8x19 - H100030 • (1) KM - CLIMBING ROPE - A100224 Phase Notes •...
Page 81
5 Ft. Ladder Attachment Phase 32 Hardware needed: Parts needed: • (2) AA - LAG SCREW WH 5/16x2-1/2 - H100028 • (1) 5 FT LADDER ASSEMBLY • (2) AC- WASHER LOCK EXT 8x19 - H100030 Phase Notes • Assemble with hardware as shown. Note: It is vital that the fort be level before and after each phase of assembly.
Page 82
Bounce Tube Attachment Phase 33 Hardware needed: Parts needed: • (4) KJ - EYEBOLT LAG WH 5/16x2 - H100135 • (1) BOUNCE TUBE ASSEMBLY • (4) CD- WASHER FLAT 8x27 - H100105 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you Note: It is vital that the fort must pre-drill each board with...
Page 83
Wave Rider Attachment Phase 34 Hardware needed: Parts needed: • (2) M - BOLT WH 5/16x2-1/2 - H100014 • (1) WAVE RIDER ASSEMBLY • (2) E - NUT BARREL WH 5/16x1-3/4 - H100007 Phase Notes • Assemble with hardware as shown. Note: It is vital that the fort be level before and after each phase of assembly.
Limited Warranty. In addition, Backyard Discovery will replace any parts within the first 30 days from date of purchase found to be missing from or damaged in the original packaging.
Need help?
Do you have a question about the Oxford 6111 and is the answer not in the manual?
Questions and answers