Remote Operation; Remote Programming (Homeowner's Phone Or Off-Site Phone); Remote Relay Activation (Off-Site Phone); Relay Activation From Homeowner's Phone - DKS 1812 Plus Installation & Owner's Manual

4.2 Remote Operation

4.2.1 Remote Programming (Home Phone or Off-Site Phone)
The 1812 can be programmed and operated from a remote location (Home or off-site) using a touch-tone telephone. Be
sure that the programming for the 1812 to answer an incoming call has not been disabled (see 2.3.9).
Note: The 1812 master code cannot be programmed remotely – it can only be programmed from the system keypad – see
Programming the Master Code on page 20.
1. Call the resident's phone number. After the programmed number of rings (2.3.9) the 1812 will answer with a tone.
2. Follow the desired programming steps in Section 2 of this manual.
3. When complete with the desired programming function, hang up. You cannot use 0# pressed together to end
programming steps from a touch-tone telephone. Wait 30 seconds before calling back to program another feature.

4.2.2 Remote Relay Activation (Off-Site Phone)

The 1812 system relays can be activated from a remote (off-site) location. Be sure that the ability for the 1812 to answer an
incoming call has not been disabled (see 2.3.9). Refer to the tone open numbers that where programmed in section 2.3.8
to determine each of the activation numbers. Only one activation number will function per phone call. Example: If you call
and want to "Hold Open" the relay, you will have to call back to "Deactivate" it later.
• Momentary Activation (Relay activates for its programmed relay strike time).
• Hold Open (Relay will activate and remain activated).
• Deactivate (Relay will deactivate).
• Hold 1 Hour (Relay will activate for 1 hour and then automatically deactivate).
To activate the relay(s) from a remote (off-site) location, perform the following steps:
1. Call the resident's phone number. After the programmed number of rings (2.3.9) the 1812 will answer with a tone.
2. Press 1 6 and enter the MASTER CODE. [
*
(Two-way voice communication is also enabled at this point)
3. Enter the desired tone open number. [ _ (beep)]
4. 1812 will automatically hang up.

4.2.3 Relay Activation from Homeowner's Phone

The 1812 system relays can be activated from the homeowner's phone. Refer to the tone open numbers that were
programmed in section 2.3.8 to determine each of the activation numbers. Only one activation number will function per
phone call. Example: If you call and want to "Hold Open" the relay, you will have to call back to "Deactivate" it later.
To activate the relay(s) from the resident's house, perform the following steps:
1. Pick up your telephone and press
2. Enter the desired tone open number (2.3.8). [ _ (beep)]
3. 1812 will automatically hang up.

4.2.4 Relay Activation Check from Homeowner's Phone

The 1812 can be called to check if relay 1, relay 2, or both relays on the 1812 main circuit board are latched and holding a
door or gate in the open (unlocked) position.
1. Pick up homeowner's telephone and press
2. Listen for the following sequence of tones:
No Tones: neither relay is activated.
Relay 1 Activated: beep - pause - beep - pause . . .
Relay 2 Activated: beep beep - pause - beep beep - pause . . .
Both Relays Activated: beep beep beep - pause - beep beep beep - pause . . .
3. Hang up.
1812-161-L-12-11
• Momentary Activation (Relay activates for its programmed strike time).
• Hold Open (Relay will activate and remain activated).
• Deactivate (Relay will deactivate).
• Hold 1 Hour (Relay will activate for 1 hour and then automatically deactivate).
7. [
*
1 6 _ _ _ _ (beep)]
*
7 (beep)]
*
7. [ 7 (beep)]
* *
35