Wiring One 1812 To The Internet - Telephone Mode - DKS 1812 Plus Installation & Owner's Manual

1.7 Wire One 1812 to the Internet - Telephone Mode
Typical "Existing"
Internet Source
Internet
Internet
DSL/Cable
Modem
Router
RJ-11
Phone
Connector
TIP (+): White/blue mark
RING (-): Blue/white mark
Phone
Jack
Access Control Devices
"Normally Open"
Vehicular
Gate Operator
Use minimum 18
AWG wire for runs
up to 100 feet.
W A
R N
IN
G
MO VIN
SER IOU G GA 16 AWG wire for
Oper S INJ TE
and ate free gate UR Y OR CAN CAU
Do not of peop only when DEA SE
or oper allow ate child le and gate obstr area TH
path Do not gate. ren to uctio is in
while stand in play in ns. sight
Read owne gate is movi gate path gate area
r's manu ng. or walk
al and throu gh
safet y instr
uctio ns.
ANS CON FOR runs up to 200 feet.
I/UL MS -325 TO
CAN CER /CSA TIFI
VEH C22 .2 ED TO
CLA ICU LAR NO. 247 53382
SS GAT
MOD EL E OPE RAT
SER HP OR
IAL
VOL TS
AMP
MAX S
GAT E LOA PHA SE
Door D 60 Hz
King , Inc.,
Ingle (Term. 11 and 13)
woo d,
CA
Pedestrian
Gate/Door
"Normally Close" with Maglock
(Terminal 15 and 16)
"Normally Open" with Electric Strike
(Terminal 14 and 16)
Magnetic locks or electric strikes must be
powered from a separate UL Listed power
transformer. DO NOT power strikes or magnetic
locks from the 1812 power transformer. Use
minimum 18 AWG wire for runs up to 100 feet;
16 AWG wire for runs up to 200 feet. It is
recommended to keep power wire runs as short
as possible.
1812-161-L-12-11
Single 1812 Wiring Configuration
EARTH
GND
1 2
CENTRAL
Internet OFFICE
Phone In
Phone In
Phone Mode
4 5 6
7 7 8 9
0
Phone Out
"Existing" Alarm
System Location
RJ31x
Phone Jack
installed
Before 1812
System
To "Existing"
Alarm Control Panel
Separate UL
Listed Power
Transformer
Electric
Strike
The 1812 Plus operates ONLY on 16.5
VAC. DO NOT power the 1812 with 24
Volt transformer or source voltage.
Use the supplied power transformer,
16.5 VAC, 20 VA (or UL listed
equivalent) to power the telephone
entry system. DO NOT power any other
devices (electric strikes, magnetic
locks, additional 1812s etc.) from the
1812's power transformer.
See page 13 for wire size and run
distances.
The By-Pass board is NOT optional and
ENTRY BY-PASS
must be installed as part of the 1812
SW1
1875-010
"Telephone Mode" system.
See page 11 for complete information.
3 4 5 6 7 8
PHONE PHONE
HOME
Single 1812:
IN OUT
Homeowner's
Phone
Phone
PHONE IN #3 connects to Main Term #1.
Out
LAN/Cordless
PHONE IN #4 connects to Main Term #2.
PHONE OUT #5 connects to Main Term #5.
PHONE OUT #6 connects to Main Term #4.
EARTH
GND
Telephone Line (Cat5e)
For complete information,
see page 12.
Cat5e
Be sure to properly ground
ALL boards. See page 13
for acceptable grounding
sources.
Ground
12 AWG Min.
Orange Pair
Supplied Transformer
Polarity does not matter.
t
t p u
O u
C
V A
. 5
1 6
V A
2 0
OUT OUT
OUTPUT
LOW VOLTAGE LINE
Ground
12 AWG Min.
Within 3 ft
of Surge Board
1878-010
By-Pass Board
ENTRY BY-PASS
SW1
1875-010
1 2 3 4 5 6 7 8
CENTRAL PHONE PHONE
HOME
OFFICE IN OUT
Orange Green
Pair Pair
Older Lines
Ground
Red Wire (-)
12 AWG Min.
Older Lines
Green Wire (+)
Main
Terminal
J1 J1
1
Phone In
RING
(1-2)
2
TIP
3
GND
4
TIP Phone Out
(4-5)
5
RING
Green Pair
6
7
1970-010
8
9
10
11
N.O.
Relay 1
12
N.C.
(11-13)
13
Com
14
N.O.
Relay 2
15
N.C.
(14-16)
16
Com
Power
17
16.5
VAC
(17-18)
18
OV
Low Voltage Surge Suppressor
DoorKing Surge Suppressor P/N 1878-010 (or
GND GND IN IN
equivalent) is optional but highly recommended.
INPUT
For best protection, surge suppressor ground wire
MUST be 3-ft. or less in length. Use minimum 12 AWG
wire. Refer to instruction sheet included with surge
board for complete information.
Check Polarity of
Telephone Line
Check for polarity on the
incoming telephone line to each
board and maintain polarity
throughout the telephone line.
One potential problem checked
when a malfunction occurs in a
telephone entry system is to
see if the telephone line has
been wired to each board with
the correct polarity.
Test Example: By-pass board's
CENTRAL OFFICE terminals #1
and #2. Terminal #2 must be
positive (Tip +) with respect to
terminal #1 (Ring -). Set a VOM
meter to measure DC volts.
Place the positive lead on
terminal #2 and the negative
lead on terminal #1. If the
meter shows a positive voltage
- OK. If the meter shows a
negative voltage (needle moves
off scale to the left), reverse the
wires on terminals #1 and #2.
Homeowner's
LAN/Cordless Phones
RING
TIP
Phone Phone
Jack Jack
Note: Each relay can control a
normally open OR normally close
access control device. Relay
contacts are rated for 3 amps @
30 VAC maximum.
15