Kurzweil PC3LE Musician's Manual page 166

Pc3le series
Table of Contents

Advertisement

Setup Mode
The Setup Editor
similarly to 1NoteAuto, except 1NoteAutoLow always latches the lowest note when holding 
multiple notes, and 1NoteAutoHi always latches the highest note when holding multiple notes. 
You can also use these latch types without a Shift Pattern if desired.
Low Key (LoKey) and High Key (HiKey)
The Arpeggiator processes notes within the range of these parameters. Notes outside the 
specified range play normally, and do not become part of the arpeggiation sequence. Set the 
LoKey and HiKey parameters using the data entry wheel or buttons.
Glissando
When the Glissando parameter is On, the Arpeggiator chromatically fills between latched notes. 
When Glissando is on, the Arpeggiator ignores the Shift Amount, Shift Limit, and Limit Option 
parameters.
You must latch at least two notes to get a result. When Glissando is on, all notes played in the 
arpeggiation range get latched, although you won't necessarily get meaningful results from all 
latched notes. In general, try to get each subsequent note you latch to be a change in direction. 
For example, try latching the following sequence of notes: C4, C5, G4, G5, C5, C6, G4, G5. The 
"glissando" changes direction around each change in direction of the latched notes.
SyncTo
The SyncTo parameter determines what an arpeggiator will sync to. An arpeggiator can sync to 
another arpeggiator, a riff, or a song playing from Song mode. You can choose a specific 
arpeggiator or riff to sync to by setting SyncTo to Arp 1–16 or Riff 1‐16, and the current 
arpeggiator will always sync to that arpeggiator or riff. For example, if you have an arpeggiator 
on a bass sound in zone 1 and an arpeggiator on a lead sound in zone 2, you may always want 
the lead arpeggiation in zone 2 to sync to the bass arpeggiation in zone 1. In this case you would 
set the SyncTo parameter in zone 2 to Arp 1.
You may want to have a little more freedom and not be tied to the bass arpeggiation in zone 1 as 
the main "timekeeper." Maybe you want to start with the lead arpeggiation in zone 2 and have 
the bass arpeggiation in zone 1 start later. In this case you would set the SyncTo parameter for 
zone 2 to FirstArp.Av. With this setting, the arpeggiator will look for the first available 
arpeggiator to sync to. So if both the bass arpeggiation and the lead arpeggiation have this 
parameter set to FirstArp.Av., the arpeggiation that is started first will be the main 
"timekeeper." If the lead arpeggiator starts first, the bass arpeggiator will see that as the first 
available arpeggiator to sync to and will do so. If the bass arpeggiator is started first, the lead 
arpeggiator will see that as the first available arpeggiator to sync to and will do so. This can be 
very handy if you are using multiple arpeggiators and want to do some live improvisation; you 
can start and stop different arpeggiators and as long is there is one arpeggiator playing, any 
arpeggiator with SyncTo set to FirstArp.Av. will sync back up when triggered again.
You can also choose FirstRiff.Av., which behaves the same way as FirstArp.Av., but makes your 
arpeggiator look for the first available riff to sync to. A setting of Main Seq. will sync the 
arpeggiator to the song currently loaded in Song mode. You can select a song in Song mode, 
then play it from setup mode with the front panel Play/Pause button. (Doing this temporarily 
replaces the programs in your setup's zones with the program used for each channel in the song, so it's 
best to make a setup that uses the same programs as your song on the same MIDI channels. If you plan on 
syncing riffs with a song, it may be easier to start by creating a setup, then recording the setup into a 
song. See Recording A Setup To Song Mode on page 7‐67 for details.) A setting of First Avail. will 
sync the arpeggiator to the first available arpeggiator, riff, or song from Song mode.
Note: If you have multiple arpeggiators or riffs already playing when using FirstArp.Av., FirstRiff.Av., 
or First Avail. for the current arpeggiator, the current arpeggiator will sync to the arpeggiator or riff of 
the lowest numbered zone that has an arpeggiator or riff playing. 
7-44

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Pc3le6Pc3le7Pc3le8

Table of Contents