Sharp AR-M355U Service Manual page 215

(Dial pulse make time setting)
1) Enter 1 with 10-key.
2) Press [START] key.
3) Enter the set value with 10-key.
4) Press [START] key.
0 EXECUTE Execute
1 MAKE TIME Dial pulse make time setting (0 - 15)
The dial signal is sent with the set value + 29ms.
When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.
SIMULATION 66-14
DIAL TEST(10PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1. MAKE TIME 7 ; [+29 ms]
Select 1 and
Select 0
press [START] key.
and press
[START] key.
SIMULATION 66-14
DIAL TEST(10PPS). SELECT 0-15, AND PRESS START.
[1. MAKE TIME]
SIMULATION 66-14
DIAL TEST(10PPS). EXECUTE
1. MAKE TIME 7 ; [+29 ms]
66-15
Purpose Setting/Operation test/Check
Function Used to set the make time in the FAX pulse dial
(Purpose) mode (20pps) and to test the dial signal output.
(The dial number signal set by SIM 66-13 is
outputted.) Used to check troubles in dialing and
to check the operation. (Only when FAX is
installed)
Section FAX
Item Operation
Operation/Procedure
1) Enter 0 with 10-key.
2) Press [START] key.
The dial signal is outputted.
(Dial pulse make time setting)
1) Enter 1 with 10-key.
2) Press [START] key.
3) Enter the set value with 10-key.
4) Press [START] key.
0 EXECUTE Execute
1 MAKE TIME Dial pulse make time setting (0 - 15)
The dial signal is sent with the set value + 9ms.
When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.
1
Press [CUSTOM SETTINGS] key
or press [START] key.
7
Press [CUSTOM SETTINGS] key.
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 79
SIMULATION 66-15
DIAL TEST(20PPS). SELECT 0-1, AND PRESS START.
0. EXECUTE
1. MAKE TIME 7 ; [+9 ms]
Select 1 and
Select 0
press [START] key.
and press
[START] key.
SIMULATION 66-15
DIAL TEST(20PPS). SELECT 0-15, AND PRESS START.
[1. MAKE TIME]
SIMULATION 66-15
DIAL TEST(20PPS). EXECUTING···.
1. MAKE TIME 7 ; [+9 ms]
66-16
Purpose Setting/Operation test/Check
Function Used to check the dial signal (DTMF) output in the
(Purpose) FAX tone dial mode. (The dial number signal set
by SIM 66-13 is outputted.) The send level can be
set to an optional level. Used to check troubles in
dialing and to check the operation. (Only when
FAX is installed)
Section FAX
Item Operation
Operation/Procedure
1) Enter 0 with 10-key.
2) Press [START] key.
The dial signal is outputted.
(Dial pulse make time setting)
1) Enter 1 or 2 with 10-key.
2) Press [START] key.
3) Enter the set value with 10-key.
4) Press [START] key.
Item
0 EXECUTE Execution
1 HIGH High group level
2 HIGH LOW High group - Low group
When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.
1
Press [CUSTOM SETTINGS] key
or press [START] key.
7
Press [CUSTOM SETTINGS] key.
Set range
0 - 15dB
0 - 15