Sharp AR-M355U Service Manual page 142

Code
Function (Purpose)
Main Sub
66 2 Used to clear the FAX soft switch function data
and to set to the default. (Excluding the
adjustment values.) (Only when FAX is installed)
3 Used to check the operation of the FAX PWB
memory (read/write). (This adjustment is required
when the PWB is replaced with a new one.) (Only
when FAX is installed)
4 Used to check the output operation of data
signals in each data output mode of FAX. (Used
to check the operation of MODEM. ) Send level:
Max. (Only when FAX is installed)
5 Used to check the output operation of data
signals in each data output mode of FAX. (Used
to check the operation of MODEM.) An output is
sent at the send level set by the soft switch. (Only
when FAX is installed)
6 Used to print the confidential pass code. (Used
when the confidential pass code is forgotten.)
(Only when FAX is installed)
7 Used to print the image memory data (memory
send/receive). (Only when FAX is installed)
8 Used to check the output operation of various
sound signals of FAX. (Used to check the
operation of the sound output IC.) Send level:
Max. (Only when FAX is installed)
9 Used to check the output operation of various
sound signals of FAX. (Used to check the
operation of the sound output IC.) An output is
sent at the send level set by the soft switch. (Only
when FAX is installed)
10 Used to clear all data of the image memory
(memory send/receive). The confidential data are
also cleared at the same time. (Only when FAX is
installed)
11 Used to check the output operation of FAX G3
mode 300bps. (Used to check the operation of
MODEM.) Send level: Max. (Only when FAX is
installed)
12 Used to check the output operation of FAX G3
mode 300bps. (Used to check the operation of
MODEM.) An output is send at the send level set
by the soft switch. (Only when FAX is installed)
13 Used to enter (set) the number of FAX dial signal
output test. (The dial number set by this
simulation is outputted when the dial signal output
test is made by SIM 66-14 - 16. ) (Only when FAX
is installed)
14 Used to set the make time in the FAX pulse dial
mode (10pps) and to test the dial signal output.
(The dial number signal set by SIM 66-13 is
outputted.) Used to check troubles in dialing and
to check the operation. (Only when FAX is
installed)
15 Used to set the make time in the FAX pulse dial
mode (20pps) and to test the dial signal output.
(The dial number signal set by SIM 66-13 is
outputted.) Used to check troubles in dialing and
to check the operation. (Only when FAX is
installed)
16 Used to check the dial signal (DTMF) output in
the FAX tone dial mode. (The dial number signal
set by SIM 66-13 is outputted.) The send level
can be set to an optional level. Used to check
troubles in dialing and to check the operation.
(Only when FAX is installed)
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 6
Code
Function (Purpose)
Main Sub
66 17 Used to check the dial signal (DTMF) output in
the FAX tone dial mode. Send level: Max. Used
to check the operation. (Only when FAX is
installed)
18 Used to check the dial signal (DTMF) output in
the FAX tone dial mode. An output is sent at the
send level set by the soft switch. Used to check
the operation. (Only when FAX is installed)
19 Used to back-up the HDD data into the Flash
memory (optional FAX expansion memory: AR-
MM9). (Only when FAX is installed)
20 Used to read the back-up data by SIM 66-19 to
the SRAM/HDD. (Only when FAX is installed)
21 Used to print information related to FAX (various
registrations, communication management, file
management, system error protocol). (Only when
FAX is installed)
22 Used to adjust the handset volume. (Only when
the FAX is installed.)
23 Used to download the FAX program. (Only when
FAX is installed)
Not used in the market. (For development)
24 Used to clear the FAST memory data. (Only when
FAX is installed)
25 Used to register the FAX number for Modem dial-
in. (Only when FAX is installed)
Not used in the market. (For development)
26 Used to register external telephone numbers for
Modem dial-in. (Only when FAX is installed)
Not used in the market. (For development)
27 Used to register the transfer number for voice
warp. (Only when FAX is installed)
Not used in the market. (For development)
29 Used to clear data related to an address book
(one-touch registration, program registration/
expansion, relay memory box registration, each
table content).
30 Used to check the change in the TEL/LIU status.
(Only when FAX is installed)
31 Used to check the relay operation. (Only when
FAX is installed)
32 Used to check the receive data (fixed data) from
the line. (Only when FAX is installed)
33 Used to check the signal (BUSY TONE/CNG/
CED/FNET/DTMF) detection. (Only when FAX is
installed)
34 Used to measure the communication time of test
image data. (Only when FAX is installed)
35 Modem program rewriting. (Only when FAX is
installed) Not used in the market. (For
development)
36 Used to check interface between MFPC controller
and MDMC. (Check of the data line or the
command line) (Only when FAX is installed)
39 Used to set the destination specifications. (Only
when FAX is installed)
42 PIC program rewriting (Only when FAX is
installed)
43 PIC adjustment value writing (Only when FAX is
installed)
67 2 Used to check the operation of the parallel I/F of
the printer. (This simulation is for production only,
and requires a special tool for execution. Not
used in the market.)
11 Used to set YES/NO of the parallel I/F select
signal of the printer.
16 Used to check the operation of the network card.