B. Simulation List - Sharp AR-M355U Service Manual

B. Simulation list

(1) Main/ Sub
Code
Main Sub
1 1 Used to check the operations of the scanner
(read) unit and its control circuit.
2 Used to check the operation of sensor and
detector in the scanning (read) section and the
related circuit.
2 1 Used to check the operations of the automatic
document feeder unit and the control circuit.
2 Used to check the operations of the sensors and
detectors in the automatic document feeder unit
and the related circuits.
3 Used to check the operations of the loads in the
automatic document feeder unit and the control
circuits.
3 2 Used to check the operation of sensor and
detector in the finisher and the related circuit.
3 Used to check the operation of the load in the
finisher and the control circuit.
6 Used to adjust the stacking capacity of the
finisher. (Used to adjust the alignment plate
(jogger) stop position in the finisher paper width
direction. The adjustment is made by changing
the alignment plate home position in the paper
width direction by software.)
10 Console finisher (AR-FN7) adjustment
20 Used to check the mail bin stacker sensor.
21 Used to check the operations of the mail bin
stacker loads.
4 2 Used to check the operations of the sensors and
detectors in the paper feed section (desk paper
feed/large capacity tray) and the related circuit.
3 Used to check the operations of the loads in the
paper feed section (desk paper feed/large
capacity tray) and the related circuit.
5 1 Used to check the operation of the display, LCD
in the operation panel, and control circuit.
2 Used to check the operation of the heater lamp
and the control circuit.
6 1 Used to check the operation of the paper
transport system loads and the control circuit.
2 Used to check the operations of each fan motor
and its control circuit.
7 1 Used to set the operating conditions of aging.
6 Used to set the intermittent aging cycle.
8 Used to set the warm-up time display YES/NO.
8 1 Used to check and adjust the operations of the
developing voltage of each color and the control
circuit.
2 Used to check and adjust the operation of the
main charger grid voltage in each printer mode
and the control circuit.
6 Used to check and adjust the operation of the
transfer voltage and the control circuit.
17 Used to check and adjust the operation of the
transfer voltage and the related circuit. (Transfer
belt cleaning mode)
9 1 Used to check and adjust the operation of the
load (clutch/solenoid) in the duplex section and
the control circuit.
2 Used to check the operations of the sensors and
detectors in the duplex section and its control
circuit.
10 1 Used to check the operations of the toner motor
and the related circuit.
Function (Purpose)
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 3
Code
Function (Purpose)
Main Sub
13 0 Used to cancel the self-diag "U1" trouble. (Only
when FAX is installed.)
14 0 Used to cancel excluding the self-diag U1/LCC/
U2/PF troubles.
15 0 Used to cancel the self-diag "U6-01, 02, 03, F3-
12, 22" (large capacity paper feed tray, paper
feed trays 1, 2) troubles.
16 0 Used to cancel the self-diag U2 troubles.
17 0 Used to cancel the PF troubles (when the copy
inhibit command from the host computer is
received).
21 1 Used to set the maintenance cycle.
22 1 Used to check the print count value in each
section and each operation mode. (Used to check
the maintenance timing.)
2 Used to check the total numbers of misfeed and
troubles. (When the number of misfeed is
considerably great, it is judged as necessary for
repair. The misfeed rate is obtained by dividing
this count value with the total counter value.)
3 Used to check misfeed positions and the misfeed
count of each position. (If the misfeed count is
considerably great, it may be judged as
necessary to repair.)
4 Used to check the trouble (self diag) history.
5 Used to check the ROM version of each unit
(section).
6 Used to output the list of the setting and
adjustment data (simulations, FAX soft switch,
counters).
7 Used to display the key operator code. (This
simulation is used when the customer forgets the
key operator code.)
8 Used to check the number of use of the finisher,
the SPF, and the scan (reading) unit.
9 Used to check the number of use (print quantity)
of each paper feed section.
10 Used to check the system configuration (option,
internal hardware).
11 Used to check the use frequency (send/receive)
of FAX. (Only when FAX is installed)
12 Used to check the SPF misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
13 Used to check the operating time of the process
section (OPC drum, DV unit, toner bottle).
19 Used to check the values of the counters related
to the scan mode and the internet FAX mode.
23 2 Used to check the trouble history of paper jam
and misfeed. (If the number of misfeed and
troubles is considerably great, it may be judged
as necessary to repair.)
80 Used to check the operations of the sensors and
detectors in the paper feed and transport section.
24 1 Used to clear the misfeed counter, the misfeed
history, the trouble counter, and the trouble
history. (The counters are cleared after
completion of maintenance.)
2 Used to clear the number of use (the number of
prints) of each paper feed section.
3 Used to clear the number of use of the finisher,
SPF, and the scan (reading) unit.
4 Used to reset the maintenance counter.
5 Used to reset the developer counter. (The
developer counter of the DV unit which is installed
is reset.)