Comtech EF Data Vipersat CDM-570 User Manual page 12

Figure 3-61 ToS Delete prompt . . . . . . . . . . . 3-46
Figure 3-62 ToS View screen . . . . . . . . . . . . . 3-47
Figure 3-63 Hitless Switching screen . . . . . . . 3-47
Figure 3-64 Set LockTime prompt . . . . . . . . . 3-48
Figure 3-65 VMS Routes in Route Table . . . . 3-49
Figure 3-66 Unit Role prompt . . . . . . . . . . . . . 3-50
Figure 3-67 Expansion Unit prompt . . . . . . . . 3-50
Figure 3-68 Network ID prompt . . . . . . . . . . . 3-51
Figure 3-69 Unit Name prompt . . . . . . . . . . . . 3-51
Figure 3-70 Receive Multicast IP Address prompt
3-52
Figure 3-71 Managing IP address menu . . . . 3-52
Figure 3-72 Vipersat Management Security screen
3-54
Figure 3-73 Encryption Key Entry prompt . . . 3-54
Figure 3-74 DPC Configuration screen (STDMA
mode). . . . . . . . . . . . . . . . . . . . . . . . . . 3-56
Figure 3-75 DPC Configuration screen (SCPC
mode). . . . . . . . . . . . . . . . . . . . . . . . . . 3-56
Figure 3-76 Calculate Max Power screen . . . 3-57
Figure 3-77 Target EbNo prompt . . . . . . . . . . 3-59
Figure 3-78 Speed Up EbNo prompt . . . . . . . 3-60
Figure 3-79 Target DPC Address prompt. . . . 3-60
Figure 3-80 Home State Configuration screen3-62
Figure 3-81 Force Modem to Home State warning
3-63
Figure 3-82 Transmit Frequency prompt . . . . 3-63
Figure 3-83 Transmit Data Rate prompt. . . . . 3-64
Figure 3-84 Transmit FEC Type prompt. . . . . 3-64
Figure 3-85 Transmit Coding Rate prompt . . . 3-64
Figure 3-86 Transmit Modulation Type prompt3-65
Figure 3-87 Transmit Power Level prompt . . . 3-65
Figure 3-88 Receive Frequency prompt . . . . . 3-66
Figure 3-89 Receive Data Rate prompt . . . . . 3-66
Figure 3-90 Receive FEC Type prompt . . . . . 3-66
Figure 3-91 Receive Coding Rate prompt . . . 3-67
Figure 3-92 Receive Modulation Type prompt 3-67
Figure 3-93 Vipersat Summary screen (Hub). 3-68
Figure 3-94 Vipersat Migration prompt . . . . . . 3-69
Figure 3-95 UDP Port Base Address prompt . 3-69
Appendix A Figures
Figure A-1 The Seven OSI Protocol Layers . . .A-2
Figure A-2 Bits and Bytes. . . . . . . . . . . . . . . . .A-4
Figure A-3 Binary to Decimal Conversion . . . .A-4
Figure A-4 IP Address Classes A, B, C . . . . . .A-7
Figure A-5 NAT Router Example . . . . . . . . . . .A-8
vi
Figure A-6 Default Subnet Masks for IP Classes .
A-9
Figure A-7 ANDing an IP address and a subnet
mask. . . . . . . . . . . . . . . . . . . . . . . . . . A-10
Figure A-8 Network Segments . . . . . . . . . . . A-10
Figure A-9 Router as Default Gateway . . . . . A-11
Figure A-10 Network Node MAC Addresses A-12
Appendix B Figures
Figure B-1 Auto Switching Menu, CDM-570/570L
Hub. . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
Figure B-2 Hub Load Switching Page, SLM-5650A
B-7
Figure B-3 Auto Switching Menu, CDM-570/570L
Remote. . . . . . . . . . . . . . . . . . . . . . . . B-10
Figure B-4 Remote Load Switching Page, SLM-
5650A. . . . . . . . . . . . . . . . . . . . . . . . . B-10
Figure B-5 Load Switching diagram . . . . . . . B-12
Figure B-6 Application Switching diagram . . B-15
Figure B-7 ToS Field Location within the IP Header
B-17
Figure B-8 Remote ToS Switching menu . . . B-19
Figure B-9 Per Device ToS Switching Example . .
B-20
Figure B-10 Per Type ToS Switching Example . .
B-21
Figure B-11 ToS Remarking Application . . . B-22
Figure B-12 ToS and DSCP Conversion Chart . .
B-22
Figure B-13 ECM Switch Recovery: < 3 minutes .
B-26
Figure B-14 ECM Switch Recovery: > 3 minutes .
B-27
Figure B-15 STDMA Page with Entry Channel
Mode, CDM-570/570L . . . . . . . . . . . . B-28
Figure B-16 ECM Remote List Page, CDM-570/
570L . . . . . . . . . . . . . . . . . . . . . . . . . . B-29
Figure B-17 Remote Bandwidth Entry, CDM-570/
570L . . . . . . . . . . . . . . . . . . . . . . . . . . B-29
Figure B-18 Revert Uplink Carrier Command, VMS
modem . . . . . . . . . . . . . . . . . . . . . . . . B-30
Figure B-19 Entry Channel Configuration, Hub . .
B-32
Figure B-20 Entry Channel Configuration, Remote
B-33
Figure B-21 ECMv2 Processing Diagram . . . B-34
Vipersat CDM-570/570L User Guide