Hitachi SJ700-2 Instruction Manual page 216

Register
Function name
No.
1301h Selection of restart mode
Allowable under-voltage power
1302h
failure time
Retry wait time before motor
1303h
restart
Instantaneous power
1304h failure/under-voltage trip alarm
enable
Number of restarts on power
1305h
failure/under-voltage trip events
1306h Phase loss detection enable
1307h
Restart frequency threshold
1308h
1309h Selection of retry after tripping
Selection of retry count after
130Ah
undervoltage
Selection of retry count after
130Bh
overvoltage or overcurrent
130Ch Retry wait time after tripping
Electronic thermal setting
130Dh (calculated within the inverter
from current output)
130Eh Electronic thermal characteristic
130Fh (Reserved)
Free setting, electronic thermal
1310h
frequency (1)
Free setting, electronic thermal
1311h
current (1)
Free setting, electronic thermal
1312h
frequency (2)
Free setting, electronic thermal
1313h
current (2)
Free setting, electronic thermal
1314h
frequency (3)
Free setting, electronic thermal
1315h
current (3)
Overload restriction operation
1316h
mode
1317h Overload restriction setting
Deceleration rate at overload
1318h
restriction
Overload restriction operation
1319h
mode (2)
131Ah Overload restriction setting (2)
Deceleration rate at overload
131Bh
restriction (2)
131Ch Overcurrent suppression enable
Active frequency matching scan
131Dh
start frequency
Active frequency matching,
131Eh
scan-time constant
Active frequency matching,
131Fh
restart frequency select
1320h Software lock mode selection
1322h (Reserved)
1323h
Run/power-on warning time
1324h
Chapter 4 Explanation of Functions
Function
R/W Monitoring and setting items Data resolution
code
0 (tripping), 1 (starting with 0 Hz), 2 (starting with
matching frequency), 3 (tripping after deceleration
b001 R/W
and stopping with matching frequency), 4 (restarting
with active matching frequency)
b002 R/W 3 to 250
b003 R/W 3 to 1000
0 (disabling), 1 (enabling), 2 (disabling during
b004 R/W
stopping and decelerating to stop)
b005 R/W 0 (16 times), 1 (unlimited)
b006 R/W 0 (disabling), 1 (enabling)
b007 (high) R/W
0 to 40000
b007 (low) R/W
0 (tripping), 1 (starting with 0 Hz), 2 (starting with
matching frequency), 3 (tripping after deceleration
b008 R/W
and stopping with matching frequency), 4 (restarting
with active matching frequency)
b009 R/W 0 (16 times), 1 (unlimited)
b010 R/W 1 to 3
b011 R/W 3 to 1000
b012 R/W 200 to 1000
0 (reduced-torque characteristic), 1 (constant-torque
b013 R/W
characteristic), 2 (free setting)
- - Inaccessible
b015 R/W 0 to 400
b016 R/W 0 to Rated current
b017 R/W 0 to 400
b018 R/W 0 to Rated current
b019 R/W 0 to 400
b020 R/W 0 to Rated current
0 (disabling), 1 (enabling during acceleration and
constant-speed operation), 2 (enabling during
b021 R/W constant-speed operation), 3 (enabling during
acceleration and constant-speed operation [speed
increase at regeneration])
b022 R/W 200 to 2000
b023 R/W 10 to 3000
0 (disabling), 1 (enabling during acceleration and
constant-speed operation), 2 (enabling during
b024 R/W constant-speed operation), 3 (enabling during
acceleration and constant-speed operation [speed
increase at regeneration])
b025 R/W 200 to 2000
b026 R/W 10 to 3000
b027 R/W 0 (disabling), 1 (enabling)
b028 R/W 200 to 2000
b029 R/W 10 to 3000
0 (frequency at the last shutoff), 1 (maximum
b030 R/W
frequency), 2 (set frequency)
0 (disabling change of data other than "b031" when
SFT is on), 1 (disabling change of data other than
"b031" and frequency settings when SFT is on), 2
b031 R/W (disabling change of data other than "b031"), 3
(disabling change of data other than "b031" and
frequency settings), 10 (enabling data changes
during operation)
- - Inaccessible
b034 (high) R/W
0 to 65535
b034 (low) R/W
4 - 153
Register
No.
-
0.1 [sec.]
0.1 [sec.]
-
-
-
0.01 [Hz]
-
-
1 [time]
0.1 [sec.]
0.1 [%]
-
-
1 [Hz]
0.1 [A]
1 [Hz]
0.1 [A]
1 [Hz]
0.1 [A]
-
0.1 [%]
0.01
sec.
[ ]
-
0.1 [%]
0.01
sec.
[ ]
-
0.1 [%]
0.01
sec.
[ ]
-
-
-
1 [10h]