Brother DCP-9010CN Service Manual page 98

Error
Problem
codes
4B Drum life end (C)
4C Drum life end soon (K)
4D Drum life end soon (Y)
4E Drum life end soon (M)
4F Drum life end soon (C)
52 Paper feeding kit life end
54 Fuser unit life end
56 Fuser cover opened
58 Fuser unit error (Some kind of
temperature error of the fuser unit occurs.)
59 Fuser unit error (Re-detection of
fuser unit failure upon startup after
the error code 58 occurs.)
5B Short paper
5C Small paper
5D Belt unit life end soon
5E Belt unit life end
5F Waste toner box near full
60 Toner life end (C)
61 Toner life end (M)
62 Toner life end (Y)
63 Toner life end (K)
64 Toner life end soon (C)
65 Toner life end soon (M)
66 Toner life end soon (Y)
67 Toner life end soon (K)
6A Fuser unit error
(The center thermistor does not detect
60 °C within the specified time.)
6B Fuser unit error
(The center thermistor does not detect
100 °C within the specified time.)
6C Fuser unit error
(The center thermistor detects higher
temperature than the specified value.)
6D Fuser unit error
(The center thermistor detects lower
temperature than the specified value.)
6F Fuser unit error
(The center or side thermistors
detect extremely high temperature.)
70 Fuser/Eject drive motor error
73 Recording ASIC read/write error
74 Toner of the color which is being used
reaches the end of life while printing.
Refer Error
to: codes
3-23 75 Machine cooling down inside
3-24 76 Fuser unit error (The center thermistor
detects rapid temperature rising.)
3-24
3-24 78 Fuser unit error
(The center thermistor detects rapid
3-24
temperature falling.)
3-24
3-24 7D Dirt on drum unit
3-25 7F FAX paper setting mismatch (The
setting paper becomes besides the
3-25
A4/Letter/Legal/Folio)
3-25 80 FAX paper size is incorrect (The
paper is smaller 10 mm than the Let-
ter size (11 inch) in Fax List/Report)
3-27
3-27 81 Incorrect density sensor measurement
value when implementing adjustment
3-27
of color density from the control panel
3-27
cover ASSY.
3-28
3-29 82 Density patch measurement is not
completed normally when implementing
3-29
adjustment of color density from the
3-29
control panel cover ASSY.
3-29
3-30 83 Drum error (K)
3-30 84 Paper jam at the back of the machine
inside
3-30
3-30 87 Toner of the color which is being
used reaches the end of life when
3-25
implementing adjustment of color
density from the control panel cover
ASSY.
3-25 88 Paper jam inside the machine
8A Paper jam in paper tray
8D Eject front sensor sticking at ON
upon startup
3-25
8E
Error in the adjustment of color
registration result when implementing it
from the control panel cover ASSY.
3-26
8F
Detection of abnormal value of
registration sensor sensitivity when
implementing adjustment of color
3-26
registration from the control panel
cover ASSY
91 Size mismatch
3-30 94 No paper in paper tray
3-31 96 No paper in all trays
3-31 97 Not supported paper
9A No paper in manual feed slot
3-6
Problem
Confidential
Refer
to:
3-32
3-26
3-26
3-32
3-35
3-35
3-36
3-36
3-14
3-37
3-31
3-37
3-38
3-38
3-39
3-39
3-39
3-40
3-40
3-40
3-41