Getting Started; Prepare Marker For Air Supply Cylinder Installation; Air Supply Cylinder Installation - Tippmann SIERRA ONE MARKER Owner's Manual

Safety Is Your Responsibility (continued from page 5)
layer will absorb some of the impact and protect you from the paintballs.
• Keep exposed skin away from escaping gas when installing or
E
removing air supply cylinder or if the marker or air supply is leaking.
N
Compressed air, CO , and nitrogen gasses are very cold and can
2
cause frostbite under certain conditions.
G
• Use only .68 caliber paintballs, never load or fire any foreign objects.
L
• Avoid alcoholic beverages before and during the use of this marker.
I
Handling markers while under the influence of drugs or alcohol is a
S
criminal disregard for public safety.
H • Avoid shooting an opponent at point blank, 6 feet or less.
• Familiarize yourself with instructions listed on air supply cylinder or
adaptor. Contact the air supply cylinder or adaptor manufacturer
with any questions.
• Read the Air Supply Cylinder Removal and SAFETY TIPS on pages
12-14 before beginning the cylinder installation.
• Always measure your marker's velocity before playing paintball and
never shoot at velocities in excess of 300 feet per second (see
instructions on page 8).

GETTING STARTED

❏ Eye protection designed for paintball use must be worn by the user and
any person within range. Do not disassemble this marker while it is
pressurized with air. Do not pressurize a partially assembled marker.
Read each step completely before performing the step.
Carefully hand start all threaded parts and do not overtighten and
strip threaded parts when assembling.
STEP 1: Prepare Marker for Air Supply Cylinder Installation
1) ❏ ❏ ❏ ❏ ❏ Install the shroud
shroud: ❏ ❏ ❏ ❏ ❏ Remove receiver bolt
❏ ❏ ❏ ❏ ❏ Replace and tighten the bolt
❏ ❏ ❏ ❏ ❏ Install the barrel (with the shroud installed): ❏ apply marker oil onto
2)
the barrel o-ring , insert the barrel into the shroud / receiver and carefully
screw it in .
before you install the barrel . To install the
and ❏ ❏ ❏ ❏ ❏ insert the shroud
to hold the shroud in place.
6
GETTING STARTED:
(continued on page 7)
GETTING STARTED: (continued from page 6)
❏ ❏ ❏ ❏ ❏ Install the collapsible stock. ❏ ❏ ❏ ❏ ❏ With the end cap cover
(slides off), ❏ ❏ ❏ ❏ ❏ Slide stock up
carefully tighten .
TO FOLD THE STOCK / TO UNFOLD THE STOCK:
1) Grip the stock with
thumb under the
hinge/latch as shown.
4) To unfold: grip the stock with thumb under the hinge/latch. Squeeze
to open latch, turn to unfolded position and release the latch to lock
in place.
STEP 2: Air Supply Cylinder Installation
❏ You must first read the Air Supply Cylinder Removal and SAFETY TIPS
on pages 12-14 before beginning the cylinder installation.
❏ ❏ ❏ ❏ ❏ Do not pressurize a partially assembled paintball marker.
.
❏ ❏ ❏ ❏ ❏ First put the trigger safety in Safe Mode (see instructions on page 4)
and ❏ ❏ ❏ ❏ ❏ install the barrel blocking device (see instructions on page 2).
❏ ❏ ❏ ❏ ❏ Next you need to cock the marker by sliding
the bolt handle all the way back until it locks into
place . Always keep marker in the cocked
position when air supply is attached to the marker.
This will help prevent an accidental discharge.
❏ ❏ ❏ ❏ ❏ To install the air supply cylinder, lubricate the cylinder valve o-ring
with a little marker oil then insert the cylinder valve end into the air
supply adapter at the back end of the marker grip. Twist the cylinder
into end cap. ❏ ❏ ❏ ❏ ❏ Insert bolt
Shorten
ADJUSTMENT:
Lengthen
Squeeze the
adjustment lever
and slide
or to lengthen stock.
2) Squeeze 3) Turn stock to right
until the latch side of receiver and
opens. release.
7

Air Supply Cylinder Installation:

(continued on page 8)
removed
and
E
N
LENGTH
G
L
I
S
H
to shorten