Getting Started; Prepare Marker For Air Supply Cylinder Installation; Air Supply Cylinder Installation; Hopper Installation - Tippmann BRAVO ONE SERIES Owner's Manual

Safety Is Your Responsibility (continued from page 5)
• Avoid alcoholic beverages before and during the use of this marker.
Handling markers while under the influence of drugs or alcohol is a
E
criminal disregard for public safety.
N
• Avoid shooting an opponent at point blank, 6 feet or less.
G
• Familiarize yourself with instructions listed on air supply cylinder or adaptor.
Contact the air supply cylinder or adaptor manufacturer with any questions.
L
• Always measure your marker's velocity before playing paintball and
I
never shoot at velocities in excess of 300 feet per second (see
S
instructions on page 8).
H

GETTING STARTED

❏ Eye protection designed for paintball use must be worn by the user and
any person within range. Do not disassemble this marker while it is
pressurized with air. Do not pressurize a partially assembled marker.
Read each step completely before performing the step:
NOTE: Carefully hand start all threaded parts and do not overtighten
and strip threaded parts when assembling.
STEP 1) Prepare Marker for Air Supply Cylinder Installation
❏ ❏ ❏ ❏ ❏ For Bravo One
TM Basic models:
. ❏ Apply marker oil onto the barrel o-ring
• Install the barrel
insert the barrel into the receiver and carefully screw it in
• For Basic marker with E-Trigger
E-Trigger Operating Instructions (on pages 8 - 10) before
TM
performing STEP 2 on page 7.
• For Basic marker without E-Trigger
• For Bravo One TM Tactical Edition models:
• Install the shroud before you install the barrel
shroud: ❏ ❏ ❏ ❏ ❏ Remove receiver bolt
Replace and tighten the bolt
• Install the barrel (with the shroud installed): ❏ apply marker oil onto
the barrel o-ring , insert the barrel into the shroud / receiver and
carefully screw it in .
• Install the collapsible stock.
❏ ❏ ❏ ❏ ❏ With the end cap cover
❏ ❏ ❏ ❏ ❏ Slide stock up
into end cap.
❏ ❏ ❏ ❏ ❏ Insert bolt
and carefully tighten .
.
TM - You must first read and follow
go to STEP 2 on page 7.
TM
. To install the
and ❏ ❏ ❏ ❏ ❏ insert the shroud. ❏ ❏ ❏ ❏ ❏
to hold the shroud in place.
removed (slides off).
6
For Tactical Edition models:
(continued on page 7)
For Tactical Edition models (continued from page 6)
• For Tactical Edition marker with E-Trigger
follow E-Trigger
performing STEP 2.
• For Tactical Edition marker without E-Trigger
STEP 2) Air Supply Cylinder Installation
• Do not pressurize a partially assembled paintball marker.
• First install the barrel blocking device (see instructions on page 2).
• Next put trigger safety in Safe Mode (see instructions on page 4).
• Next you need to cock the marker
by sliding the bolt handle all the
,
way back until it locks into place
Always keep marker in the cocked
position when air supply is attached
to the marker. This will help prevent
an accidental discharge.
• To install the air supply cylinder, lubricate the cylinder valve o-ring
with a little marker oil then insert the cylinder valve end into the air
supply adapter at the back end of the marker grip. Twist the cylinder
clockwise
fire once you switch to Fire Mode from Safe Mode. If the tank is full
and you do not hear the air supply engage, the pin valve could be too
short or the pin valve seal is damaged.
STEP 3) Hopper Installation
• Barrel blocking device must be installed (see page 2) and safety in Safe
Mode (see page 4) before filling the hopper.
• Make sure that the feed elbow and hopper are clean and free of any
sharp edges to keep paintballs feeding into the marker smoothly.
• Install the hopper neck into the feed elbow of your marker and
tighten the hopper down with a 3/16" allen wrench
with your marker.
NOTE: Do not overtighten or the elbow may break. ❏ ❏ ❏ ❏ ❏ With the barrel
Shorten
Lengthen
Squeeze the
adjustment lever
and slide
or
TM - You must first read and
TM Operating Instructions (on pages 8-10) before
TM
.
into the marker until it stops. Your marker is ready to
7
Hopper Installation (continued on page 8)
Length
Adjustment:
E
N
G
L
I
to shorten
to lengthen stock.
S
H
go to STEP 2.
included