Marker Disassembly / Assembly - Tippmann SIERRA ONE MARKER Owner's Manual

Storage: (continued from page 15)
install the barrel blocking device (see page 2). You should store your
marker in a dry area. Before storing your marker make sure that the
E
marker is cleaned and oiled (see cleaning and maintenance on page
N 15) so that it does not rust. Store your marker with the bolt in the
forward position, uncocked (see below).
G
❏ When removing your marker out of storage make sure the trigger safety
L
is in Safe Mode (see page 4) and the barrel blocking device is installed
I
(see page 2). You should re-oil the rear bolt o-ring and the front bolt o-ring
before use (see cleaning and maintenance on page 15).
S

Marker Disassembly / Assembly

H
❏ Eye protection designed for paintball use must be worn by the user
and any person within range during disassembly / assembly.
First follow ❏ Unloading Your Marker and ❏ Air Supply Cylinder
Removal instructions on pages 12-14. Do not disassemble a pressurized
paintball marker. Do not pressurize a partially
assembled paintball marker.
❏ Put the marker into the uncocked position.
To uncock the marker: Pull and hold the bolt
cocking handle back
trigger and release the handle slowly forward
which will uncock the marker.
NOTE: Carefully hand start all threaded parts and do not overtighten and
strip threaded parts when assembling.
TA06209 Collapsible Stock Assembly
(Replaces End Cap Cover )
TA09919
Bolt
Collapsible Stock Assembly not
Shown In basic parts pages 10-11).
- then pull the
NOTE: (if 2 adapter bolts
removed, the short bolt goes in front
when reassembling).
16
Marker Disassembly (continued on page 17)
Marker Disassembly (continued from page 16)
❏ Remove the barrel
press the 2 tabs
until it stops. ❏ Loosen the 2 adapter bolts
elbow , press the feed lock
the receiver.
❏ To remove the left-side receiver
unscrew bolt
bolts ( 3 long -
receiver to access the internal parts.
❏ With left half removed, pull the end cap out to remove the guide pin
and drive spring (these parts must be removed before the bolt handle
can be removed). Disconnect the linkage arm from the rear and front
bolts. Slide the front bolt off the power tube and check the o-ring.
Clean and oil the o-ring or if damaged, replace with a new one. Do the
same with the rear bolt o-ring.
Power tube and valve removal.
NOTE: Do not remove the gas line fitting unless it is leaking or you need
to replace the valve. If you should do so you will need some teflon tape or
paste to reinstall it. Carefully hand start all threaded parts and do not
overtighten and strip threaded parts when assembling.
❏ First, complete Marker Disassembly Instructions (see page 16).
❏ Power tube removal: To remove the power tube
and valve, unscrew
bolts from the right side receiver.
❏ Valve removal from power tube: If it is necessary to remove the valve,
use a wrench
fitting is out, the valve will slide out the back of the power tube.
NOTE: ❏ Check the external valve o-ring and if damaged, replace
with a new one. If the o-ring is damaged your marker will not function
correctly. ❏ Clean all parts and oil the o-rings.
❏ Reinstall the valve into the power tube: Insert cleaned and oiled
valve into the power tube and align the holes of the valve and
power tube. ❏ Apply teflon tape or paste on threads of gas line
fitting and carefully screw it into the valve and snug with a wrench
(do not over tighten and strip threaded parts). ❏ Wipe
off any excess paste.
❏ Reinstall the power tube/valve into receiver: align the holes of the
power tube and the right receiver half, apply red loctite #271 sealant to
are
threads of two valve lock bolts
tighten bolts and strip threads. ❏ Wipe off any excess paste.
. ❏ Remove the magazine
unscrew
in and slide it out. ❏ Turn the velocity screw
, tilt the feed elbow out and slide it off
: ❏ Remove the rear sight
and slide off. ❏ Unscrew
the 6 receiver connection
) + (3 short - ). Then carefully lift the left-side
the two valve lock
to slowly unscrew the gas line fitting. Once the
and attach
17
,
in
E
. ❏ Remove the feed
N
G
L
I
S
H
- do not over
Marker Disassembly / Assembly
(continued on page 18)