Korg microSAMPLER Owner's Manual page 24

microSAMPLER
MONO/ST ............................................................................ [MONO/STEREO]
This selects either monaural or stereo sampling.
This parameter is related to the global parameter AUDIO IN setting and also
to the AUDIO IN [ /LINE] switch setting.
When the [INPUT SELECT] button indicates AUDIO IN
Global [ /LINE]
[AUDIO IN] switch
L/MONO LINE
L/MONO
STEREO LINE
STEREO
When the [INPUT SELECT] button indicates RE-SAMPLE
MONO
The stereo output mixed to monaural will be resampled in mono.
STEREO
Sample in stereo.
You can't change the stereo/mono setting of a sample. You must specify the
stereo/mono setting before you start sampling.
TRIGGER .............................[SMPL SW, NOTE ON, THRE 01...10, KEY GATE]
This selects how sampling will be initiated.
SMPL SW (Sampling SW)
From sampling setup mode, press the [SAMPLING] button to begin
sampling.
NOTE ON
From sampling-setup mode, press the [SAMPLING] button to enter
sampling-standby mode; sampling will begin when you play the key-
board.
THRE 01...10 (Threshold 1...10)
From sampling-setup mode, press the [SAMPLING] button to enter
sampling-standby mode; sampling will begin automatically when the
signal exceeds the audio level you specified for Threshold 1...10.
This is convenient when you're sampling while playing another instru-
ment, or when you want to avoid capturing the sound of the microSAM-
PLER being operated (e.g., the sound of a button being pressed).
24
The sound that's sampled
STEREO
MONO
L
[L/MONO] [L/MONO] [L/MONO]
[ MIC] [ MIC] [
[L] + [R] [L/MONO] [R]
[ MIC] [ MIC] [
The cursor will momentarily blink when the specified audio level is
exceeded while in the sampling-standby mode.
KEY GATE
This will be specified automatically if SAMPLING TYPE is set to "KEY
GATE."
If SAMPLING TYPE is set to "AUTO NEXT," settings other than THRE 01...10
cannot be selected.
TIME (Sampling Time) .........................[1/64...8/1, 0.1...159.7 sec (at 48K)]
R
This specifies the sampling time. Values [1/64 through 8/1] are divisions of
the beat, as determined by the current BPM setting. Values [0.1 through
MIC]
159.7] are given in seconds. For Loop and Auto Next sampling, set the micro-
SAMPLER's BPM to match the tempo of the sample source before sampling.
MIC]
Immediately after the power is turned on, the display will indicate the avail-
able sampling time. Once you've sampled, the new remaining time will be
shown. You can specify the sampling time with this remaining time as the
maximum.
LEVEL (Sampling Level) ................................................[–INF dB...+12.0 dB]
This adjusts the level for sampling.
From sampling setup mode, adjust the level so that the sampling level
meter's clip indication does not light.
FX POS (Fx Position) ..................................................... [MST FX, AUDIO IN]
This specifies the position of the effect when sampling.
MST FX (Master FX)
Choose this if you want to resample with an effect applied to the sample.
When you're not performing a sampling operation, the effect will oper-
ate as MST FX (Master FX) regardless of this setting.
AUDIO IN
Choose this if you want to sample from AUDIO IN with an effect
applied.
This setting applies only in sampling-setup, sampling-standby, and dur-
ing sampling.
If you choose the "AUDIO IN" setting, set the effect parameters from
sampling-setup mode.
The effect sound may be interrupted if you enter sampling-setup mode
when FX POS is set to "AUDIO IN," or if you switch the FX POS setting while in
sampling-setup mode.