Korg microSAMPLER Owner's Manual: Load Sample; Normalize

Hide thumbs
microSAMPLER

5. LOAD SAMPLE

LOAD.SMPL .......................................................[FROM.BNK.A...H, R (ROM)]
LOAD.SMPL ............................................................[FROM.S.AL, S.01...S.36]
This loads sample data from the specified bank into the current sample
that's selected.
1.
Press the [EDIT] button to make it blink.
If the [EDIT] button is not blinking, press it again until it blinks.
2.
Use the [PARAMETER/FX CONTROL 1] knob to select the "SAMPLE"
page.
3.
Press the [EDIT] button to make it light-up.
4.
Use the [PARAMETER/FX CONTROL 1] knob to select the
"LOAD.SMPL" page.
5.
Use the [VALUE/FX CONTROL 2] knob to select the bank that contains
the sample you want to load.
6.
Press the [ENTER/SHIFT] button.
If there are no samples in the bank you selected, the display will indicate
"ERROR NO.SAMPLE." Press the [EXIT] button to return to step 5, and
select a different bank.
7.
Use the [VALUE/FX CONTROL 2] knob to select the sample that you
want to load.
FROM S.AL
All samples will be selected.
FROM S.01...S.36
Select one of the 36 samples.
If no sample exists for the number, an "*." is shown before the sample
number instead of "S."
8.
Press the [ENTER/SHIFT] button.
9.
When the display asks "SURE?," press the [ENTER/SHIFT] button once
again to confirm. If you decide to cancel, press the [EXIT] button to
return to step 7.
When the sample data has been loaded, the screen will indicate "COM-
PLETE."
Do not operate the microSAMPLER's knobs, buttons, or keyboard while
this operation is being executed. Never turn off the power during this
time.
32
6. NORMALIZE
NORMALIZ (Normalize) .............................................................. [–6...+6 dB]
This amplifies the sample's level as much as possible without causing dis-
tortion, and then applies the specified gain to the current sample (☞p.18) of
the selected bank.
1.
Press the [EDIT] button to make it blink.
If the [EDIT] button is not blinking, press it again until it blinks.
2.
Use the [PARAMETER/FX CONTROL 1] knob to select the "SAMPLE"
page.
3.
Press the [EDIT] button to make it light-up.
4.
Use the [PARAMETER/FX CONTROL 1] knob to select the "NOR-
MALIZ" page.
5.
Use the [VALUE/FX CONTROL 2] knob to specify the gain.
6.
Press the [ENTER/SHIFT] button.
7.
When the display asks "SURE?," press the [ENTER/SHIFT] button once
again to confirm. If you decide to cancel, press the [EXIT] button to
return to step 5.
When the sample data has been normalized, the screen will indicate
"COMPLETE."
It is not possible to restore the sample to its previous state after perform-
ing the Normalize operation. If you save the sample (☞p.41 "Saving
(writing)") before normalizing it, you'll be able to recover the original
data by executing LOAD.SAMPLE (☞p.32 "5. LOAD SAMPLE") if the
results are not what you expected.
Maximum level

Advertising

   Related Manuals for Korg microSAMPLER

Comments to this Manuals

Symbols: 0
Latest comments:
  • Mel J Dec 11, 2015 04:20:
    Just what I'm looking for bought a S/H unit with no manual
  • Mel J Dec 11, 2015 04:20:
    Just what I'm looking for bought a S/H unit with no manual
  • Yu Gwang Jae Oct 02, 2014 07:25:
    Thank You very much
    Thank You very much
    Thank You very much
    Thank You very much
    Thank You very much