Korg microSAMPLER Owner's Manual: Pitch Bend; Control Change

Hide thumbs

3. Pitch bend

Pitch bend change [En, bb, mm]
(n: channel, bb: lower byte of value, mm: upper byte of value)
In Keyboard mode, pitch bend change messages can be received to control
the pitch (the range is fixed at 1 octave).
In this case, the pitch is controlled in the range from –8192 to +8191, with
mm=64 and bb=00 as the zero value (center). (This message is received on
the channel specified by the "GLOBAL" page KB.MIDI.CH parameter.)
Pitch bend change messages cannot be received in Sample mode.
4. Control change
Knob control change assignment [Bn, cc, vv]
(n: channel, cc: control change number, vv: value)
Control change messages will be transmitted when you operate the
[PARAMETER/FX CONTROL 1] knob (CC#12) or the [VALUE/FX CON-
TROL 2] knob (CC#13).
If you've assigned effect parameters to these knobs, incoming messages of
the control change number assigned to a knob will control the correspond-
ing effect parameter.
These messages are transmitted and received on the global MIDI channel.
Volume (CC#07) [Bn, 07, vv]
In Keyboard mode, volume messages can be received to control the volume.
Volume messages cannot be received in Sample mode. This message is
received on the keyboard MIDI channel.
Panpot (CC#10) [Bn, 0A, vv]
In Keyboard mode, panpot messages can be received to control the pan posi-
tion.
Panpot messages cannot be received in Sample mode. This message is
received on the keyboard MIDI channel.
All note off (CC#123) [Bn, 7B, 00] (value is 00)
When an All Note Off message is received, notes that are playing on that
channel will turn off. Depending on the settings, the release portion of the
notes may still be heard.
All sound off (CC#120) [Bn, 78, 00] (value is 00)
When an All Sound Off message is received, all sound being produced by
that channel will turn off. While the All Note Off message allows the release
portion of the notes to be heard, the All Sound Off message will silence the
sound immediately.
These messages are intended for use in emergencies such as when "stuck
notes" occur. They are not used during normal performance.
Reset all controllers (CC#121) [Bn, 79, 00] (value is 00)
When a Reset All Controllers messages is received, all controller values
being used on that channel will be reset.
5. Parameters transmitted and received as NRPN mes-
sages
NRPN (Non Registered Parameter Number) messages are assigned to the
microSAMPLER's knobs and buttons that are not covered by the controllers
discussed above. Each musical instrument manufacturer or device is free to
use NRPN messages as desired.
To edit using NRPN messages, use the following procedure.
1.
Transmit NRPN MSB (CC#99) [Bn, 63, mm] and NRPN LSB (CC#98)
[Bn, 62, register] messages (n: channel, mm, rr: upper and lower bytes of
the parameter number) to specify the desired parameter.
2.
Transmit a data entry MSB (CC#6) [Bn, 06, mm] message (n: channel,
mm: parameter value) to set the value of the specified parameter.
The microSAMPLER uses only the data entry MSB.
MIDI guide
45

Advertising

   Related Manuals for Korg microSAMPLER

Comments to this Manuals

Symbols: 0
Latest comments:
  • Mel J Dec 11, 2015 04:20:
    Just what I'm looking for bought a S/H unit with no manual
  • Mel J Dec 11, 2015 04:20:
    Just what I'm looking for bought a S/H unit with no manual
  • Yu Gwang Jae Oct 02, 2014 07:25:
    Thank You very much
    Thank You very much
    Thank You very much
    Thank You very much
    Thank You very much