Korg microSAMPLER Owner's Manual Page 51

Hide thumbs
5. DECIMATR (Stereo Decimator)
By lowering the sampling frequency and bit depth, this effect reproduces the
rough sound of an inexpensive sampler. It simulates the distinctive noise
produced by such samplers.
Wet: Stereo In - Stereo Out
Left
Pre LPF
Bit
Decimator
Sampling Frequency
LFO
Decimator
Pre LPF
Bit
Right
DRY/WET
.............................................................. [DRY, 99:1...1:99, WET]
Adjusts the balance between the effect sound and the direct sound.
PRE LPF ........................................................................................... [OFF, ON]
Specifies whether the aliasing noise produced by lowering the sampling rate
will be heard.
On samplers that have a low sampling frequency, inputting frequencies that
are too high to be reproduced will generate pitches that are unrelated to the
original sound. By turning PRE LPF "ON," you can prevent such noise from
being generated.
By setting FS to about "3 kHz" and turning PRE LPF "OFF," you can pro-
duce a sound reminiscent of a ring modulator.
HI DAMP ........................................................................................ [0...100%]
Adjusts the high-frequency damping.
FS
....................................................................................... [1.0...48.0 kHz]
Specifies the sampling frequency.
BIT
............................................................................................. [4...24 bit]
Specifies the bit depth of the data.
Lower settings will make the sound rougher and more distorted. Some set-
tings may change the volume, so adjust OUT.LEVEL if necessary.
OUT.LEVEL (Output Level) ...............................................................[0...127]
Adjusts the output level.
Dry / Wet
High Damp
Output Level
High Damp
Output Level
Dry / Wet
FS.MOD.INT (Mod Intensity)
.................................................. [–63...+63]
Adjusts the depth of the modulation applied by the LFO to the sampling fre-
quency.
LFO SYNC (LFO Tempo Sync) ......................................................... [OFF, ON]
☞p.48 "LFO SYNC (LFO Tempo Sync)"
LFO FREQ (LFO Frequency)
.........................................[0.01...100.00 Hz]
☞p.48 "LFO FREQ (LFO Frequency)"
This parameter will be visible and editable if LFO SYNC is "OFF."
SYNC. NOTE (LFO Sync Note)
.................................................[8/1...1/64]
☞p.48 "SYNC.NOTE (LFO Sync Note)"
This parameter will be visible and editable if LFO SYNC is "ON."
LFO WAVE (LFO Waveform) ............[SAW, SQUARE, TRIANGLE, SINE, S&H]
☞p.48 "LFO WAVE (LFO Waveform)"
LFO. SHAPE ................................................................................... [–63...+63]
Adjusts the LFO waveform.
KEY SYNC (LFO Key Sync) .............................................................. [OFF, ON]
☞p.49 "KEY SYNC (LFO Key Sync)"
INI.PHASE (LFO Init Phase) ............................................................. [0...180º]
☞p.49 "INI.PHASE (LFO Init Phase)"
This parameter will be visible and editable if "KEY SYNC" is ON.
6. Reverb
This effect simulates the reverberant ambience of a hall or similar space.
Wet: Mono In - Stereo Out
Left
Trim
Trim
Right
Effect parameters
Dry / Wet
Reverb
Dry / Wet
51

Advertising

   Related Manuals for Korg microSAMPLER

Comments to this Manuals

Symbols: 0
Latest comments:
  • Mel J Dec 11, 2015 04:20:
    Just what I'm looking for bought a S/H unit with no manual
  • Mel J Dec 11, 2015 04:20:
    Just what I'm looking for bought a S/H unit with no manual
  • Yu Gwang Jae Oct 02, 2014 07:25:
    Thank You very much
    Thank You very much
    Thank You very much
    Thank You very much
    Thank You very much