Korg microSAMPLER Owner's Manual Page 60

Hide thumbs

Advertisement

microSAMPLER
18. GRAIN.SFT (Grain Shifter)
This effect samples the sound at extremely brief intervals and loops the play-
back. This is particularly good with sounds that are constantly changing,
such an external audio input.
Wet: Mono In - Mono Out
Left
+
Right
DRY/WET
.............................................................. [DRY, 99:1...1:99, WET]
Adjusts the balance between the effect sound and the direct sound.
BPM SYNC (Duration Tempo Sync) ............................................... [OFF, ON]
Specifies whether the looped playback of the waveform will be synchro-
nized.
If this is "ON," the looped playback of the waveform will synchronize to the
tempo or to MIDI clock.
TM RATIO (Time Ratio)
Specifies the length of the waveform's looped playback as a proportion of
the DURATION setting.
DURATION ..................................................................[0...350ms, 1/64...1/1]
Specifies the length of the waveform that will be played.
The actual length played is determined by this setting together with the TM
RATIO setting.
If BPM SYNC is "OFF," you can set this in a range of "0–350 ms."
If BPM SYNC is "ON," you can set this as a resolution relative to the tempo
specified by "2. Setting the tempo" (☞p.18) or by MIDI clock.
If the combined DURATION and TM RATIO settings would exceed the allow-
able limit, a " " symbol is shown at the right of the DURATION and TM RATIO
values.
60
Dry / Wet
Grain Shifter
Sample Cycle
Dry / Wet
LFO
................ [BPM SYNC OFF: 0.5...400.0% (OVER)
/BPM SYNC ON: 12.5...400.0% (OVER)]
LFO SYNC (LFO Tempo Sync) ......................................................... [OFF, ON]
☞p.48 "LFO SYNC (LFO Tempo Sync)"
LFO FREQ (LFO Frequency)
.........................................[0.01...100.00 Hz]
This specifies the rate in Hz units at which the waveform will be switched if
LFO SYNC is "OFF."
The length of waveform specified by DURATION will be played as a loop,
and the waveform will switch to the next length at each cycle of the LFO.
LFO Cycle
Duration
In
Out
For some settings of the LFO FREQ and SYNC.NOTE parameters, it may take
some time before the effect sound is output when you switch the FX POS
setting (☞p.24) while in sampling-setup mode.
If this parameter is assigned to a knob, turning LFO SYNC ON will change the
assignment to SYNC NOTE.
SYNC.NOTE (LFO Sync Note)
..................................................[8/1...1/64]
☞p.48 "SYNC.NOTE (LFO Sync Note)"
KEY SYNC (LFO Key Sync) .............................................................. [OFF, ON]
☞p.49 "KEY SYNC (LFO Key Sync)"
INI.PHASE (LFO Init Phase) .............................................................[0...180º]
☞p.49 "INI.PHASE (LFO Init Phase)"
LFO Cycle / Duration

Advertisement

   Related Manuals for Korg microSAMPLER

Comments to this Manuals

Symbols: 0
Latest comments:
  • Mel J Dec 11, 2015 04:20:
    Just what I'm looking for bought a S/H unit with no manual
  • Mel J Dec 11, 2015 04:20:
    Just what I'm looking for bought a S/H unit with no manual
  • Yu Gwang Jae Oct 02, 2014 07:25:
    Thank You very much
    Thank You very much
    Thank You very much
    Thank You very much
    Thank You very much