Korg microSAMPLER Owner's Manual Page 55

Hide thumbs
L DELAY, R DELAY (L, R Delay Time) ...................... [0...1400 ms, 1/64... 1/1]
☞p.53 "L DELAY, C DELAY, R DELAY (L, C, R Delay Time)"
FEEDBACK
....................................................................................[0...127]
☞p.53 "FEEDBACK"
MOD.DEPTH
.................................................................................[0...127]
Adjusts the depth of modulation.
LFO FREQ (LFO Frequency)
.........................................[0.01...100.00 Hz]
Specifies the LFO frequency. Higher values will make the LFO faster.
LFO SPRD (LFO Spread) ............................................................ [–180...180º]
Specifies the LFO phase difference between the left and right channels.
11. TAPE.ECHO
This effect simulates a tape echo. It reproduces the distortion and tonal
change that are characteristic of magnetic tape.
Wet: Mono In - Stereo Out
Left
Feedback
Tape
Saturation
Trim
Pre Tone
High / Low Damp
Wow Flutter
Right
DRY/WET
.............................................................. [DRY, 99:1...1:99, WET]
Adjusts the balance between the effect sound and the direct sound.
BPM SYNC (Delay Time Tempo Sync) ........................................... [OFF, ON]
☞p.52 "BPM SYNC (Delay Time Tempo Sync)"
TM RATIO
..................................... [BPM SYNC OFF: 0.5...400.0% (OVER)
/BPM SYNC ON: 12.5...400.0% (OVER)]
☞p.52 "TM RATIO (Time Ratio)"
Dry / Wet
Tap1 Level
Delay
Spread
Tap2 Level
Dry / Wet
TAP1 DLY,TAP2 DLY(Tap1,Tap2 Delay Time) .........[0...1400 ms, 1/64...1/1]
Specify the delay times for tap 1 and tap 2. The delay time is determined by
these values in conjunction with the TM RATIO value.
TAP1 LVL,TAP2 LVL (Tap1 Level,Tap2 Level)
Adjust the output levels of tap 1 and tap 2.
FEEDBACK
.................................................................................... [0...127]
Adjusts the amount of feedback for tap 1.
HI DAMP ........................................................................................ [0...100%]
Specifies the amount of high-frequency damping.
LO DAMP ....................................................................................... [0...100%]
Specifies the amount of low-frequency damping.
TRIM .................................................................................................. [0...127]
Adjusts the input level to the effect.
SATURATN (Tape Saturation)
..................................................... [0...127]
Adjusts the amount of distortion in the effect sound.
WOW FREQ (WOW Flutter Frequency) ............................[0.01...100.00 Hz]
Adjusts the speed of pitch change in units of Hz.
WOW.DEPTH (WOW Flutter Depth) ................................................ [0...127]
Adjusts the depth of pitch change.
PRE TONE .......................................................................................... [0...127]
Adjusts the tone of the input sound.
SPREAD ............................................................................................. [0...127]
☞p.53 "SPREAD"
Effect parameters
............................. [0...127]
55

Advertising

   Related Manuals for Korg microSAMPLER

Comments to this Manuals

Symbols: 0
Latest comments:
  • Mel J Dec 11, 2015 04:20:
    Just what I'm looking for bought a S/H unit with no manual
  • Mel J Dec 11, 2015 04:20:
    Just what I'm looking for bought a S/H unit with no manual
  • Yu Gwang Jae Oct 02, 2014 07:25:
    Thank You very much
    Thank You very much
    Thank You very much
    Thank You very much
    Thank You very much