Download Print this page

Installation - Maytag 23-11-2214N-002 User Manual

Room air conditioners for double-hung windows
Hide thumbs

Advertisement

Installation°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°
2. SUPPORT
PLATFORM
ASSEMBL Y
D
Three
(3) 3/8"
long
sel|
apping
screws
Machine
screws
__
_,
Support
platform
_
plate
II _
Support
angle
Leveling
bolt
The above installations are intended to be permanent,
and when installed in apartment or rental properties,
permission to make the above modifications should be
obtained from owners or landlords
of buildings prior
to installation of unit.
Support
platform
assembly
!
..............
El
Foam seal
J
J
J
oP retainer
Filler
panel
Sliders
Sliding
Window
Installation
1. Choose
the installation
site. It is imperative
that window
frame
assembly
and side of structure
are adequate
to support
weight
of
unit.
Reinforce
if necessary.
2. Slide open
one window
sash to install
support
platform.
3.
Attach
support
platform
to sill plate with three
(3) 3/8" long
self-
tapping
screws (Fig. 3).
4.
Loosely attach
support
angle
to bottom
of support
platform
using
two (2) 7/16"
long machine
screws, flat washers,
and nuts.
S.
Place support
platform
against
lower window
track and firmly
against
vertical
edge of window
frame (Fig. 4).
6.
Attach
support
platform
to window
sill using two (2) 1" long self-
tapping
screws (Fig. 4). To overcome
interference
of support
plat-
form with window
track or storm
window,
securely
attach
a 2"
wide
shim strip to the window
sill. Strip should
be as long as
width
of support
platform
and flush with back edge of sill.
Thickness
of strip should
be controlled
by amount
of interfer-
ence.
7.
Pull support
angle
against
outside
of structure.
Tighten
two (2)
7/16"
long machine
screws on top of support
platform
(Fig. 3).
8.
Adjust leveling
bolt to position
support
angle in a level plane.
This will allow for prop angle. Tighten
leveling
bolt locknut
(Fig.
3).
Important:
Unit must
be level
or tilted
back slightly
to facilitate
prop-
er condensate
disposal.
Caution:
Do not drill
a hole
in bottom
pan.
Unit
is designed
to oper-
ate with
approximately
1/2" of water
in bottom
pan.
9.
Cut
two
pieces
of adhesive
back
foam
seal to height
of window
opening.
Remove
backing
and
apply
to vertical
inside
edges
of
window
frame
and
sliding
sash
that
will
rest
against
unit
(Fig.
S).
10. Slide
unit
onto
support
platform.
Be sure
unit
side
channel
butts
against
vertical
edge
of window
frame.
Note: If unit side channel
does
not fit securely,
remove
unit and read-
just
leveling
bolt.
11. Drill
two
1/8"
holes
through
window
channel
frame
in align-
ment
with
existing
holes
in bottom
bar. Install
two
(2) 3/8"
long
self-tapping
screws
through
these
holes.
If window
channel
frame
is not
tall
enough
to use
existing
holes,
drill
(2) new
holes
off to
the
side
of the
existing
holes
to attach
the
unit
bottom
bar to the
support
platform.
Unit
should
be firmly
anchored
to window
channel
frame
or support
platform
(Fig.
6).
12. Slide
inside
window
sash
closed.
Be sure
vertical
edge
of inside
window
sash
is pressed
firmly
against
side
of unit
cabinet.
Cut
remaining
adhesive
back
foam
seal to width
of window
opening.
Remove
backing
and
apply
to top
inside
edge
of win-
dow
frame
(Fig. S).
2

Advertisement

loading

  Related Manuals for Maytag 23-11-2214N-002