Table of Contents
Advertisement
Available languages
Available languages
Installation°°°°°°°°°°°°°
13.
D
Drilled holes
14.
Support
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
Install
speed clips on top and bottom
inside
edge of window
to
provide
locking
(Fig. 7).
Using
supplied
plastic
foam seal, cut to proper
length,
insert
between
inside
window
sash and outside
window
(Fig. 7).
1S. Place top retainer
on top edge of filler panel,
(Fig. S) then
place the bottom
edge of filler panel
into groove
of bottom
retainer
(mounted
on unit).
Filler panel
may be trimmed
with
knife or scissors to fit window
height.
16.
Slide sliders upward
making
sure filler panel
aligns in sliders.
17.
With sliders up against
top retainer,
drill 1/8" hole through
window
frame in alignment
with
existing
hole in slider. Install
3/8" long self-threading
screw in hole. Repeat
for other
slider.
18.
Check
all seals and plug all air leaks around
unit.
Use supplied
sealant
to fill any minor
openings.
Window
channel
frame
Casement
Window
Installation
D
Speed clip
Channel
Drilled
holes
3/8" long
screws
This
air conditioner
is designed
to fit into
most
casement
type
win-
dows.
As shipped
from
factory,
unit
will
fit into
a minimum
window
opening
1S 1/2"
wide
and
22" high.
The
preferred
method
of instal-
lation
is through
a closed
or stationary
window.
Installation
in an
open
window
frame
is also
possible
where
open
window
can
be
secured
to outside
of building
or removed
completely.
1. Closed
or Stationary
Window:
Install
unit
in stationary
sash
to
avoid
crank
handles
or window
latches.
If unit
is to be installed
in or
next
to a movable
sash,
it may
be necessary
to remove
catch,
handle
or both.Remove
crank
handle
and
secure
window
in closed
postion.
Remove
glass
panes
and
separating
strips
to a height
sufficient
to
mount
unit.
2. Open
Window
Frame:
Remove
crank
mechanism
and
catch
han-
dles.
Fold
window
sash
back
against
exterior
wall
of building
and
secure,
or remove
completely
where
possible.
3. A filler
panel
will be required
at side
of unit
when
installed
in
windows
having
width
greater
than
1S 1/2".
Filler
panel
should
be
made
from
3/4"
thick
wood
securely
anchored
to one
side
of open-
ing
so that
1S 1/2"
wide
opening
is provided.
Filler
panel
should
run
full length
of window.
Paint
to suit.
4. Install
unit
in same
manner
as described
for sliding
windows.
Installation
in Wood
Sliding
or
Wood
Casement
Windows
1. For wood frame casement
windows,
it is necessary
to construct
a
frame,
using
at least 1" thick wood with
a 1S 1/2" wide opening.
2. Paint frame
and fasten
it securely,
sealing it into window
opening.
3. Install
unit into frame following
procedures
for metal sliding
and
casement
windows.
Caution:Do not block air circulation to outside
louvers of cabinet.
These installations
are also typical,
and since styles and sizes of case-
ment
windows
vary widely,
it is advisable
to have unit installed
by
someone
skilled
in this type of installation.
The dealer
selling
these
units
can recommend
or supply
qualified
people
to install
your new
unit.
3
- Quick Links:
- Operation
Hide quick links:
Advertisement
Table of Contents
