Extron electronics CrossPoint 450 Plus Series User Manual page 92

SIS ™ Programming and Control, cont'd
Command/response table for SIS commands (continued)
Command
Audio output volume
N The table on the next page defi nes the value of each audio volume step.
N You can set the output volume to whole dB values only, using the
X#
level ( +V and
audio output volume commands are reported in whole dB levels only; the reported
higher magnitude value (for example, 3.5 dB is reported as 4 dB.
Set audio volume to a
specifi c value
Example:
Increment value
Example:
Decrement volume
Read output volume
Audio mute
Audio mute
Audio unmute
Read audio mute
Global audio mute
Global audio ummute
Names
Write global preset name
Example:
Read global preset name
Example:
Write room name
Example:
Read room name
Write room preset name
Example:
Read room preset name
•
N
If a preset is unassigned, then
•
If a global preset is saved, but not yet named, the default name is Preset
•
If a room preset is saved, but not yet named, the default name is RM
Write input name
Example:
Read input name
Write output name
Example:
Read output name
CrossPoint 450 Plus and MAV Plus Switchers • SIS Programming and Control
4-10
ASCII command
(host to switcher)
X#
-V) commands increase and decrease the volume in steps of 0.5 dB only. The
X# X&
* V
1*50v
X#
+V
1+V
X#
-V
X#
V
X#
*1Z
X#
*0Z
X#
Z
1*Z
0*Z
EX1! X2! }
, NG
E }
1,Security 1NG
EX1! }
NG
E }
2NG
EX* X2! }
, NR
E }
1,Classrm 1NR
EX* }
NR
EX* X1@ X2! }
* , NP
E }
1*2,Podium_DVDNP
EX* X2! }
* NP
X2!
displays [unassigned].
EX! X2! }
, NI
E }
1,Podium cam1NI
EX! }
NI
EX# X2! }
, NO
E }
1,Main PJ1NO
EX# }
NO
Response Additional
description
(switcher to host)
X# X&
* V command. The increment and decrement
X&
value is rounded up to the next
X#• X&]
Out Vol
• ]
Set output 1 volume to 79%.
Out01 Vol50
X#• X&]
Increase volume by 0.5 dB.
Out Vol
• ]
Increment audio volume
Out01 Vol51
0.5 dB, from 79% to 80.5%.
X#• X&]
Decrease volume by 0.5 dB.
Out Vol
X&]
X# ]
Amt *1 Mute audio output
(audio off).
X# ]
Amt *0 Unmute audio output
(audio on).
X(]
1 = mute on, 0 = mute off.
]
Mute all audio outputs.
Amt1
]
Unmute all audio outputs.
Amt0
X1! X2!]
Nmg ,
]
Name global preset 1
Nmg01,Security 1
"Security 1".
X2!]
]
Security 2
X* X2!]
Nmr ,
]
Name room 1 "Classrm 1".
Nmr01,Classrm 1
X2!]
X* X1@ X2!]
Nmp * ,
]
Nmp01*03,Podium_DVD
Name room 1, preset 3
"Podium_DVD".
X2!]
•X1!
.
X*• X1@
Prst .
X! X2!]
Nmi ,
]
Name input 1 "Podium cam".
Nmi01,Podium cam
X2!]
X# X2!]
Nmo ,
]
Name output 1 "Main PJ1".
Nmo01,Main PJ1
X2!]
X&
values for all
X#
X#