Lexmark T632 Service Manual page 42

4060-xxx
Base printer sub error codes (continued)
First 6 bytes sub error
code data (xx can be
any value)
84 xx 17
84 xx 18
84 xx 19
84 xx 1A
84 xx 1B
84 xx 1C
84 xx 1D
84 xx 1E x1 x2
84 xx 20 x1 x2
84 xx 21 x1 x2
2-8
Service Manual
Explanation
There is an envelope or envelopes in the envelope feeder during warm up. An
envelope may have partially fed from the envelope feeder.
Remove any envelopes from the feeder and check the envelope feeder for correct
operation.
There is media over the Tray 2 pass thru sensor during warm up. Check for media
over the sensor. If no media is present, check the pass thru sensor, flag, and
cables.
• Try running the Input Tray Tests for Tray 2 and see if Tray 2 is feeding paper
correctly and all the sensors are working correctly.
• Make sure the paper size setting is correct for the size paper in the tray.
There is media over the Tray 3 pass thru sensor during warm up. Check for media
over the sensor. If no media is present, check the pass thru sensor, flag, and
cables.
• Try running the Input Tray Tests for Tray 3 and see if Tray 3 is feeding paper
correctly and all the sensors are working correctly.
• Make sure the paper size setting is correct for the size paper in the tray.
There is media over the Tray 4 pass thru sensor during warm up. Check for media
over the sensor. If no media is present, check the pass thru sensor, flag, and
cables.
• Try running the Input Tray Tests for Tray 4 and see if Tray 4 is feeding paper
correctly and all the sensors are working correctly.
• Make sure the paper size setting is correct for the size paper in the tray.
There is media over the Tray 5 pass thru sensor during warm up. Check for media
over the sensor. If no media is present, check the pass thru sensor, flag, and
cables.
• Try running the Input Tray Tests for Tray 5 and see if Tray 5 is feeding paper
correctly and all the sensors are working correctly.
• Make sure the paper size setting is correct for the size paper in the tray.
There is media over the Tray 6 pass thru sensor during warm up. Check for media
over the sensor. If no media is present, check the pass thru sensor, flag, and
cables.
• Try running the Input Tray Tests for Tray 6 and see if Tray 6 is feeding paper
correctly and all the sensors are working correctly.
• Make sure the paper size setting is correct for the size paper in the tray.
The envelope feeder pass thru sensor never deactivated. The display of this code
indicates that an envelope never crossed over the sensor flag and passed beyond
the sensor, or the flag and sensor are not operating properly. Go to
feeder service check" on page
The envelope feeder pass thru sensor was never activated.
(x1=media size, x2=media source)
Make sure envelopes are feeding over the sensor. If an envelope feeds over the
sensor but the sensor does not activate, check the sensor and flag for correct
operation. If the sensor and flag are operating correctly, go to
service check" on page 2-49.
The imaged page is not the expected page.
(x1=media size, x2=media source)
Check the pass thru sensor to make sure it is operating properly. If no problem is
found, it may be necessary to try a new pass thru sensor.
The smart tray x did not pick a sheet of paper.
(x1=media size, x2=media source)
Check tray x auto compensator and tray parts for correct operation. If no problem
is found, go to "Input tray(s) service check" on page
2-49.
2-64.
"Envelope
"Envelope feeder