DAELIM S2-250 Service Manual page 15

SERVICE INFORMATION
TORQUE VALUES
ENGINE
ITEM
CYLINDER HEAD BOLT A
CYLINDER HEAD BOLT B
OIL FILTER SCREEN CAP
EXHAUST MUFFLER JOINT LOCK NUT
CYLINDER HEAD CAP NUT
VALVE ADJUST LOCK NUT
CAM CHAIN TENSIONER SLIPER BOLT
OIL BOLT
CLUTCH OUTER NUT
CLUTCH DRIVE PLATE NUT
FLYWHEEL NUT
OIL PUMP BOLT
CYLINDER HEAD COVER BOLT
SPARK PLUG
WATER PUMP IMPELLER
CAM CHAIN TENSIONER BOLT
MUFFLER TORQUE BOLT
FRAME
ITEM
STEERING STEM NUT
STEERING TOP THREAD NUT
FORK PIPE BOTTOM BRIDGE
HANDLE POST
FRONT AXLE NUT
FRONT CALIPER BRACKET BOLT
FRONT MASTER CYLINDER HOLDER BOLT
FRIBT DISK PLATE BOLT
REAR AXLE NUT
REAR CALIPER BRACKET BOLT
REAR MASTER CYLINDER HOLDER BOLT
REAR DISK PLATE BOLT
SPEEDOMETER GEARBOX SCREW
FRONT FORK BOLT
REAR CUSHION UPPER BOLT
REAR CUSHION UNDER BOLT
REAR CUSHION LOCK NUT
ENGINE HANGER UPPER BOLT
ENGINE HANGER LOWER BOLT
MAINSTAND BOLT
SIDESTAND PIVET SEREW
SIDESTAND PIVET NUT
Torque values listed above are for specific tightening points. Torque values for other items are listed in the following table.
1-12
THREAD DIA
Q'TY
(mm)
2 8
2 8
1 30
2 8
4 8
2 5
1 6
1 12
1 12
1 12
1 14
2 5
4 6
1 10
1 6
1 8
2 8
1 10
THREAD DIA
Q'TY
(mm)
1 26
1 26
1 10
2 10
1 12
2 8
2 6
3 8
1 16
2 8
2 6
3 8
1 5
2 22
2 10
2 10
2 10
2 12
1 10
2 10
1 10
1 10
TORQUE VALUE REFERENCE
3.0 kgf·m
3.0 kgf·m
1.47 kgf·m
2.2 kgf·m
2.45 kgf·m
1.1 kgf·m
1.0 kgf·m
1.27 kgf·m
5.5 kgf·m
5.5 kgf·m
5.88 kgf·m
0.5 kgf·m
1.18 kgf·m
1.72 kgf·m
1.18 kgf·m
1.18 kgf·m
2.8 kgf·m
4.0 kgf·m
TORQUE VALUE REFERENCE
7.0 kgf·m
0.25 kgf·m
7.5 kgf·m
6.0 kgf·m
6.0 kgf·m
3.1 kgf·m
1.2 kgf·m
4.25 kgf·m
12.5 kgf·m
3.1 kgf·m
1.2 kgf·m
4.25 kgf·m
0.43 kgf·m
2.25 kgf·m
4.0 kgf·m
4.0 kgf·m
3.5 kgf·m
5.25 kgf·m
4.5 kgf·m
4.0 kgf·m
1.5 kgf·m
4.5 kgf·m
Initial torque