User Settings; What Are The Settings You Need; Entering The User Settings Menu - Visonic POWERMAXPRO User Manual

USER SETTINGS

7. User Settings

What are the Settings You Need?

The installer provides you with a ready-to-use alarm
system, but a few settings and adjustments will still
be needed.
Note: Although the
responsibility, you may request your installer to
perform them for you (except for the user codes which
you would like to keep secret).
The user settings include (if enabled by the installer):
•
Bypassing zones - determining which zones
will be bypassed (disabled) during the present
disarm period and the next armed period.
•
Reviewing the bypass list - "show bypass" -
displaying the numbers and names of bypassed
zone one by one.
•
Recalling the last bypassing scheme - "recall
bypass" - re-using the previous bypassing
scheme, which
disarming but is still saved in the PowerMax Pro
memory.
Note: RECALL BYPASS is applicable when
partition is disabled.
•
Private report* - determining the event groups
to be reported to private telephone subscribers.
Determining the 1
numbers to which the system will report event
messages that were defined by the system
installer. Determining the number of times the
called party's private telephone number is
dialed. Determining whether or not 2-way voice
communication with private telephones will be
allowed. Determining whether to use a single
acknowledge signal, or, an acknowledge signal
from each telephone before the current event is
considered reported. Determining the 1
th
and 4 SMS telephone numbers to which pre-
selected event types will be reported.
•
Setting user codes* - programming a security
code for yourself and additional 7 codes for
other system users. Codes 5 through 8 are
"Latchkey" user codes (see Chapter 2 - Arming
in the Latchkey Mode for additional details).
•
Enrolling keyfob transmitters* - teaching the
PowerMax Pro system to recognize the ID code of
each keyfob transmitter (multi-button, CodeSecure™
type, wireless transmitter), so that the PowerMax Pro
can respond to commands transmitted by them.
•
Enrolling proximity tags* - teaching the
PowerMax Pro to recognize the ID of each
proximity tag so that the PowerMax Pro can
respond to proximity tags presentation.
•
Setting voice options* - enabling or disabling
verbal announcements (prompts).
•
Auto arm option* - enabling or disabling
automatic arming (at a predefined time).
26
user settings are
becomes suspended
st nd rd th
, 2 , 3 and 4 telephone
st
, 2
•
Setting auto arm time* - selecting automatic
arming time.
•
Using squawk option* - enabling/disabling
LOW/MID/HI squawk (short siren sound) upon
arming and disarming by keyfob. All the options are
your
applicable for wireless siren. For wired siren, refer
to LOW, MID and HI options as "squawk enable".
•
Setting the time and time format* - adjusting
the built-in clock to show the correct time and
time format.
•
Setting the date and date format* - adjusting
the built-in calendar date and date format.
•
Setting the scheduler* - setting schedule for
devices start/stop activation.
*
This option can be accessed only if master user
code has been entered.
after

Entering the User Settings Menu

Figure 7 describes how to enter User Settings menu
(when all zones/partitions are secured).
Click the keys that you are instructed to press. The
resultant display is shown below each instruction
Instruction: Enter 4-digit master
user code (default "1111"), or
user code (see note below).
These menu items are displayed
only if "bypass" was enabled by
the installer.
RECALL BYPASS is applicable
when partition is disabled.
nd rd
, 3
* Menu items that are marked
with an asterisk can be
accessed only if master
user code has been entered.
* * I N S TA L L E R M O DE i s
displayed only if USER
PERMIT ENABLE was
selected by the installer.
Figure 7 – Entering User Settings Menu
READY 00:00
WALK TEST
USER SETTINGS
ENTER CODE _ _ _ _
[master/ user code]
SET BYPASS
SHOW BYPASS
RECALL BYPASS
(*)
PRIVATE REPORT
(*)
SET USER CODES
(*)
ENROLL KEYFOB
(*)
ENROLL PROX TAG
(*)
SET VOICE OPTION
(*)
AUTO ARM OPTION
(*)
AUTO ARM TIME
(*)
SQUAWK OPTION
(*)
SET TIME&FORMAT
(*)
SET DATE&FORMAT
(*)
SCHEDULER
(*) (**)
INSTALLER MODE
<OK> TO EXIT
D-302542