Reporting To Private Telephone - Visonic POWERMAXPRO User Manual

SPECIAL FUNCTIONS
B. Executable Commands
Command
1 Disarm
2 Arm home
3
Arm Home instant
4
Arm AWAY
5
Arm AWAY instant
6
Arm AWAY Latchkey
7 Arm AWAY Latchkey instant
8 Query system status
9 Turn light xx ON, xx=[01...15]
10 Turn light xx OFF, xx=[01...15]
11 Turn PGM ON
12 Turn PGM OFF
13 Two-way voice communication
14 Playback recorded message
15 Start record message
16 Stop record message
17 Erase recorded message
18 Quit
C. Two-Way Voice Communication
Perform steps 1-6
Communication above and continue as follows:
1. [ ] [7] [ #]
2. Wait for 2 beeps
3. [3] or [1] or [6] (see below)
The system will start to function in the "LISTEN IN"
mode, letting you hear the sounds within your
residence for 50 seconds. If the person under
surveillance happens to speak or cry then, you will
hear this. You can switch the system to Listen-In,
Speak Out or Full Duplex, as shown in the next table.
Command
Listen-in (listening to the person at home) (*)
Speak-out (speaking to the person at home) (*)
Full-duplex (listening & speaking) (*)
Note: To prolong the communication session
by 50 seconds, press [3], [1] or [6] again, as
required.
* The 2-way communication can be terminated by
anyone close to the PowerMax Pro, by disarming
the system.
Remark Regarding Listen-in & Speak-out modes
Listen-in & Speak-out modes allow one way speech
at a time. Back and forth exchange of uninterrupted
speech between two parties is a method normally
used in military, commercial and amateur radio
22
Single Partition Keying
Sequence
[*]→[0]→[p#]→[1]→[#]
[*]→[0]→[p#]→[2]→[#]
Not supported command
[*]→[0]→[p#]→[3]→[#]
Not supported command
Not supported command
Not supported command
Not supported command
[*]→[5]→[xx]→[1]→[#]
[*]→[5]→[xx]→[0]→[#]
[*]→[5]→[00]→[1]→[#]
[*]→[5]→[00]→[0]→[#]
[*]→[7]→[#]
[*]→[8]→[1]→[#]
[*]→[8]→[2]→[#]
[*]→[8]→[3]→[#]
[*]→[8]→[4]→[#]
[*]→[9]→[9]→[#]
in Establishing Telephone
communication. Once you finish talking you should
say "Go Ahead" or "Over" and then switch from
speak-out to listen in. When the person at home
finishes talking he should also say "Over", as a cue
to you to switch back from Listen-in to speak out.
EXAMPLE:
You (at remote telephone):
can you hear me? Are you in any trouble? Over"....
[3]
Person at home: "Yes, I am. I had a dizzy spell while
trying to get out of bed and fell on the floor. I am
unable to get up and my thigh hurts. Can you help
me? Over"...
You (at remote telephone):
Key
send someone right away, stay put - over"..
[3]
Person at home: "Thanks, please hurry, over".
[1]
You (at remote telephone):
[6]
and out".....
IMPORTANT! If you wish to exit the two-way
communication
command, just press [ ] and then key your user
code followed by the command (see "keying
sequences" in Executable Commands table above).

Reporting to Private Telephone

control
panel
All Partitions Keying Sequence /
Partition Disable
[*]→[1]→[#]
[*]→[2]→[#]
[*]→[2]→[1]→[#]
[*]→[3]→[#]
[*]→[3]→[1]→[#]
[*]→[4]→[#]
[*]→[4]→[1]→[#]
[*]→[9]→[#]
[*]→[5]→[xx]→[1]→[#]
[*]→[5]→[xx]→[0]→[#]
[*]→[5]→[00]→[1]→[#]
[*]→[5]→[00]→[0]→[#]
[*]→[7]→[#]
[*]→[8]→[1]→[#]
[*]→[8]→[2]→[#]
[*]→[8]→[3]→[#]
[*]→[8]→[4]→[#]
[*]→[9]→[9]→[#]
[1], "Hey, George,
[1], "Sure, I will
[1], "All right, over
[ ] 9] [9] (END OF SESSION)
mode and execute
[3].
another
D-302542