Multi-Function Transmitter; Proximity Tag; Voice Announcements - Visonic POWERMAXPRO User Manual

Note regarding the Mute Speaker button
The Mute Speaker button is active only if the "Set
Voice Option" function is enabled ("enable prompts" -
see user setting flow-chart, fig. 8).

Multi-Function Transmitter

Your system responds to signals sent by a 4-button
(MCT- 234) or a 6-button two-way (MCT- 237)
'keyfob' transmitter, or by a two-way wireless keypad
(MKP-150/151) - see figure 4.
The MCT-234 keyfob transmitter is used to control
single or multiple predefined partition(s) only. The
MCT-237 keyfob transmitter and the two-way
wireless keypad can control a single or any
combination up to 3 partitions.
MCT-234
DISARM
AWAY
HOME
AUX
MKP-150 /151
Figure 4. Keyfob Transmitters and Keypad
A PANIC alarm can be initiated: through the MCT-
234 keyfob, by pressing AWAY and HOME together
for 2 sec.; through the MCT-237 keyfob, by pressing
the AUX1 and AUX2 buttons for 2 sec.; and through
the MKP-150/151 keypad by pressing the # and *
buttons for 2 sec. Pressing AWAY twice within 2
seconds initiates Latchkey arming, if enabled by the
installer. The devices can be used for:
A. Controlling a gate or another electrical
device: Pressing the AUX button opens/closes
an electrically-controlled gate, or controls a
chosen electrical d.
B. Arming the system in the INSTANT mode:
Pressing the AUX button immediately after
arming, during exit delay, causes the system to
be armed without an entry delay. This means
that entering the protected premises via any
D-302542
MCT-237
DISPLAY
DISARM
PARTITION
SELECTION
AWAY
AUX 2
HOME
AUX 1
AWAY
zone will trigger an immediate alarm. You and
other holders of keyfob transmitters will have no
problem, because you can disarm the system
before entering by pressing the DISARM (
button on your transmitter before entry.
C. Getting status information: Upon pressing the
aux button on your transmitter, the control panel
announces the
loudspeaker. When partition is enabled, the
control panel announces the status of the
partition to which the keyfob is enrolled.
D. Skip exit delay: Pressing the AUX button will
immediately cause the system to arm "instant".
Disarming by a keyfob whose battery voltage is
low (if enabled by the installer)
If you try to disarm the system with a keyfob whose
battery voltage is low, a protest beep will be heard for
15 seconds. During this period you should press again
the disarm button of the keyfob or control panel (for the
control panel, user code is required) to disarm the
system. If you perform this action during the 15 seconds
period, the Low Bat acknowledge message will be
stored in the event log.
If the disarm button is not pressed again during the
15 seconds period, perform either of the following
actions when you want to rearm the system:
A. Press AWAY twice to arm the system, otherwise
the system will
acknowledgement (from the user that he knows
about the Low Bat) will not be stored in the event
log.
B. Press AWAY and then press disarm button, to
acknowledge, otherwise the acknowledgement
will not be stored in the event log.

Proximity Tag

Your system responds to valid proximity tags enrolled to
the system. The proximity tag enables you to perform a
variety of functions without entering user code, for
example, arming, disarming, reading the event log, etc.
Whenever the user code is required, you can simply
present a valid proximity tag and perform the desired
operation without the need to key-in your user code.

Voice Announcements

The pre-recorded voice announcements respond to
your commands by announcing what the system is
doing and by prompting you to perform certain
actions. They also announce alarms, troubles and
identify the source of each event.
INTRODUCTION
system status over
not be armed and
)
the
an
7