Effects Parameters - Yamaha 01V96i Reference Manual

132
Appendix: Parameter Lists

Effects Parameters

REVERB HALL, REVERB ROOM,
REVERB STAGE, REVERB PLATE
One input, two output hall, room, stage, and plate
reverb simulations, all with gates.
Parameter Range
REV TIME 0.3–99.0 s
INI. DLY 0.0–500.0 ms
HI. RATIO 0.1–1.0
LO. RATIO 0.1–2.4
DIFF. 0–10
DENSITY 0–100%
E/R DLY 0.0–100.0 ms
E/R BAL. 0–100%
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
GATE LVL OFF, –60 to 0 dB
ATTACK 0–120 ms
1
HOLD
2
DECAY
1. 0.02 ms–2.13 s (fs=44.1 kHz), 0.02 ms–1.96 s (fs=48 kHz),
0.01 ms–1.06 s (fs=88.2 kHz), 0.01 ms–981 ms (fs=96 kHz)
2. 6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
EARLY REF.
One input, two output early reflections.
Parameter Range
S-Hall, L-Hall, Ran-
TYPE dom, Revers, Plate,
Spring
ROOMSIZE 0.1–20.0
LIVENESS 0–10
INI. DLY 0.0–500.0 ms
DIFF. 0–10
DENSITY 0–100%
ER NUM. 1–19
FB.GAIN –99 to +99%
HI. RATIO 0.1–1.0
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
01V96i—Reference Manual
Description
Reverb time
Initial delay before reverb begins
High-frequency reverb time ratio
Low-frequency reverb time ratio
Reverb diffusion (left–right
reverb spread)
Reverb density
Delay between early reflections
and reverb
Balance of early reflections and
reverb (0% = all reverb, 100% =
all early reflections)
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Level at which gate kicks in
Gate opening speed
Gate open time
Gate closing speed
Description
Type of early reflection simula-
tion
Reflection spacing
Early reflections decay character-
istics (0 = dead, 10 = live)
Initial delay before reverb begins
Reflection diffusion (left–right
reflection spread)
Reflection density
Number of early reflections
Feedback gain
High-frequency feedback ratio
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
GATE REVERB, REVERSE GATE
One input, two output early reflections with gate,
and early reflections with reverse gate.
Parameter Range
TYPE Type-A, Type-B
ROOMSIZE 0.1–20.0
LIVENESS 0–10
INI. DLY 0.0–500.0 ms
DIFF. 0–10
DENSITY 0–100%
HI. RATIO 0.1–1.0
ER NUM. 1–19
FB.GAIN –99 to +99%
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
MONO DELAY
One input, two output basic repeat delay.
Parameter Range
DELAY 0.0–2730.0 ms
FB. GAIN –99 to +99%
HI. RATIO 0.1–1.0
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
SYNC OFF, ON
1
NOTE
1.
(Max. value depends on tempo setting)
Description
Type of early reflection simula-
tion
Reflection spacing
Early reflections decay character-
istics (0 = dead, 10 = live)
Initial delay before reverb begins
Reflection diffusion (left–right
reflection spread)
Reflection density
High-frequency feedback ratio
Number of early reflections
Feedback gain
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Description
Delay time
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feed-
back)
High-frequency feedback ratio
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine DELAY