Yamaha 01V96i Reference Manual page 137

DYNA. PHASER
Two input, two output dynamically controlled
phaser.
Parameter Range
SOURCE INPUT, MIDI
SENSE 0–100
DIR. UP, DOWN
1
DECAY
OFFSET 0–100
FB.GAIN –99 to +99%
2, 4, 6, 8, 10, 12,
STAGE
14, 16
LSH F 21.2 Hz–8.00 kHz
LSH G –12.0 to +12.0 dB
HSH F 50.0 Hz–16.0 kHz
HSH G –12.0 to +12.0 dB
1. 6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
REV+CHORUS
One input, two output reverb and chorus effects in
parallel.
Parameter Range
REV TIME 0.3–99.0 s
INI. DLY 0.0–500.0 ms
HI. RATIO 0.1–1.0
DIFF. 0–10
DENSITY 0–100%
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
REV/CHO 0–100%
FREQ. 0.05–40.00 Hz
AM DEPTH 0–100%
PM DEPTH 0–100%
MOD. DLY 0.0–500.0 ms
WAVE Sine, Tri
SYNC OFF, ON
1
NOTE
1.
Description
Control source: input signal or
MIDI Note On velocity
Sensitivity
Upward or downward fre-
quency change
Decay speed
Lowest phase-shifted frequency
offset
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feed-
back)
Number of phase shift stages
Low shelving filter frequency
Low shelving filter gain
High shelving filter frequency
High shelving filter gain
Description
Reverb time
Initial delay before reverb begins
High-frequency reverb time ratio
Spread
Reverb density
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Reverb and chorus balance (0%
= all reverb, 100% = all chorus)
Modulation speed
Amplitude modulation depth
Pitch modulation depth
Modulation delay time
Modulation waveform
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine FREQ.
Effects Parameters
REV->CHORUS
One input, two output reverb and chorus effects in
series.
Parameter Range
REV TIME 0.3–99.0 s
INI. DLY 0.0–500.0 ms
HI. RATIO 0.1–1.0
DIFF. 0–10
DENSITY 0–100%
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
REV.BAL 0–100%
FREQ. 0.05–40.00 Hz
AM DEPTH 0–100%
PM DEPTH 0–100%
MOD. DLY 0.0–500.0 ms
WAVE Sine, Tri
SYNC OFF, ON
1
NOTE
1.
REV+FLANGE
One input, two output reverb and flanger effects in
parallel.
Parameter Range
REV TIME 0.3–99.0 s
INI. DLY 0.0–500.0 ms
HI. RATIO 0.1–1.0
DIFF. 0–10
DENSITY 0–100%
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
REV/FLG 0–100%
FREQ. 0.05–40.00 Hz
DEPTH 0–100%
MOD. DLY 0.0–500.0 ms
FB. GAIN –99 to +99%
WAVE Sine, Tri
SYNC OFF, ON
1
NOTE
1.
137
Description
Reverb time
Initial delay before reverb begins
High-frequency reverb time ratio
Spread
Reverb density
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Reverb and chorused reverb bal-
ance (0% = all chorused reverb,
100% = all reverb)
Modulation speed
Amplitude modulation depth
Pitch modulation depth
Modulation delay time
Modulation waveform
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine FREQ.
Description
Reverb time
Initial delay before reverb begins
High-frequency reverb time ratio
Spread
Reverb density
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Reverb and flange balance (0% =
all reverb, 100% = all flange)
Modulation speed
Modulation depth
Modulation delay time
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feed-
back)
Modulation waveform
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine FREQ.
01V96i—Reference Manual