Yamaha 01V96i Reference Manual page 138

138
Appendix: Parameter Lists
REV->FLANGE
One input, two output reverb and flanger effects in
series.
Parameter Range
REV TIME 0.3–99.0 s
INI. DLY 0.0–500.0 ms
HI. RATIO 0.1–1.0
DIFF. 0–10
DENSITY 0–100%
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
REV.BAL 0–100%
FREQ. 0.05–40.00 Hz
DEPTH 0–100%
MOD. DLY 0.0–500.0 ms
FB. GAIN –99 to +99%
WAVE Sine, Tri
SYNC OFF, ON
1
NOTE
1.
REV+SYMPHO.
One input, two output reverb and symphonic effects
in parallel.
Parameter Range
REV TIME 0.3–99.0 s
INI. DLY 0.0–500.0 ms
HI. RATIO 0.1–1.0
DIFF. 0–10
DENSITY 0–100%
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
REV/SYM 0–100%
FREQ. 0.05–40.00 Hz
DEPTH 0–100%
MOD. DLY 0.0–500.0 ms
WAVE Sine, Tri
SYNC OFF, ON
1
NOTE
1.
01V96i—Reference Manual
Description
Reverb time
Initial delay before reverb begins
High-frequency reverb time ratio
Spread
Reverb density
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Reverb and flanged reverb bal-
ance (0% = all flanged reverb,
100% = all reverb)
Modulation speed
Modulation depth
Modulation delay time
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feed-
back)
Modulation waveform
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine FREQ.
Description
Reverb time
Initial delay before reverb begins
High-frequency reverb time ratio
Spread
Reverb density
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Reverb and symphonic balance
(0% = all reverb, 100% = all
symphonic)
Modulation speed
Modulation depth
Modulation delay time
Modulation waveform
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine FREQ.
REV->SYMPHO.
One input, two output reverb and symphonic effects
in series.
Parameter Range
REV TIME 0.3–99.0 s
INI. DLY 0.0–500.0 ms
HI. RATIO 0.1–1.0
DIFF. 0–10
DENSITY 0–100%
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
REV.BAL 0–100%
FREQ. 0.05–40.00 Hz
DEPTH 0–100%
MOD. DLY 0.0–500.0 ms
WAVE Sine, Tri
SYNC OFF, ON
1
NOTE
1.
REV->PAN
One input, two output reverb and autopan effects in
parallel.
Parameter Range
REV TIME 0.3–99.0 s
INI. DLY 0.0–500.0 ms
HI. RATIO 0.1–1.0
DIFF. 0–10
DENSITY 0–100%
THRU,
HPF
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF
THRU
REV.BAL 0–100%
FREQ. 0.05–40.00 Hz
DEPTH 0–100%
1
DIR.
WAVE Sine, Tri, Square
SYNC OFF, ON
2
NOTE
1. L<–>R, L–>R, L<–R, Turn L, Turn R
2.
Description
Reverb time
Initial delay before reverb begins
High-frequency reverb time ratio
Spread
Reverb density
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Reverb and symphonic reverb
balance (0% = all symphonic
reverb, 100% = all reverb)
Modulation speed
Modulation depth
Modulation delay time
Modulation waveform
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine FREQ.
Description
Reverb time
Initial delay before reverb begins
High-frequency reverb time ratio
Spread
Reverb density
High-pass filter cutoff frequency
Low-pass filter cutoff frequency
Reverb and panned reverb bal-
ance (0% = all panned reverb,
100% = all reverb)
Modulation speed
Modulation depth
Panning direction
Modulation waveform
Tempo parameter sync on/off
Used in conjunction with TEMPO
to determine FREQ.