Yamaha 01V96i Reference Manual page 144

144
Appendix: Parameter Lists
REV-X Hall, REV-X Room, REV-X Plate
This is a 2-in/2-out reverb algorithm. It provides
rich, high-density reverberation with a smooth
decay, and depth and spaciousness that will enhance
the original sound. You can choose one of three pro-
grams to suit the venue and your needs: REV-X Hall,
REV-X Room, and REV-X Plate.
Parameter Range
REV TIME 0.32–32.14s
INI.DLY 0.0–125.0ms
DECAY 0–53
ROOMSIZE 0–28
DIFF. 0–10
HPF Thru–8.00 kHz
LPF 1.00 kHz–Thru
HI.RATIO 0.1–1.0
LO.RATIO 0.1–1.4
LO.FREQ. 22.0 Hz–18.0 kHz
Level
meter
MIX 0–100%
01V96i—Reference Manual
Description
Specifies the duration of time
until the reverberation decays to
silence. Higher values produce
longer reverberation
Specifies the time delay from
when the original sound is input
until reverberation begins.
Higher values produce a longer
delay before reverberation
begins
Specifies the shape of the rever-
beration's envelope. This value
will affect the characteristics of
the reverberation
Specifies the size of the space.
Higher values simulate a broader
space. This value is linked with
the Reverb Time. Changing this
value will also change the Reverb
Time
Specifies the density and diffu-
sion of the reverberation. Higher
values will increase the density
and strengthen the sense of spa-
ciousness
This is a filter that cuts the
low-frequency range of the
reverberation. The region below
the frequency specified here will
be cut. This filter does not affect
the original sound
This is a filter that cuts the
high-frequency range of the
reverberation. The region above
the frequency specified here will
be cut. This filter does not affect
the original sound
Adjusts the decay time of the
high-frequency reverberation.
This specifies the high-fre-
quency decay time as a propor-
tion of the Reverb Time
Adjusts the decay time of the
low-frequency reverberation.
This specifies the low-frequency
decay time as a proportion of
the Reverb Time
Specifies the frequency on which
Lo Ratio is based. The region
below this frequency will be
affected by the Lo Ratio
Use the METER: [IN] [OUT]
switches to choose whether the
input level or output level will be
shown
Adjusts the balance between the
original sound and the effect
sound.
Only the original sound will be
output if this value is 0%, and
only the effect sound will be out-
put if this value is 100%
Max 100
This is a 1-in/1-out phaser that emulates a vintage
effect that was manufactured only during the late
1970s.
Parameter Range
MODE 1, 2, 3, 4
SYNC,
SPEED
0.100–10.000 Hz
Vintage Phaser
This is a 1-in/1-out phaser that offers an extremely
high level of freedom in creating phaser sounds,
without limiting itself to emulating any particular
model.
Parameter Range
SPEED SYNC, 0.1–10.0 Hz Adjusts the rate of modulation
MANUAL 0.00–10.00
DEPTH 0.00–10.00
FEEDBACK 0.00–10.00
COLOR 0.00–10.00
MODE 1, 2
STAGE 4, 6, 8, 10
Description
Switches the sound quality
(tone). There are four types
available, each with differences
in modulation amplitude and in
the amount of feedback
Adjusts the rate of modulation
Description
Adjusts the center frequency of
modulation
Adjusts the depth of modulation
Adjusts the amount of feedback
This parameter is available for
certain combinations of MODE
and STAGE. It allows you to
fine-tune the tonal character
Selects the type of circuit config-
uration being modeled. This will
affect the tonal character
Specifies the number of stages in
the circuit being modeled. This
will affect the tonal character