RST Instruments RSTAR Affinity Installation And User Manual page 5

Figure 47: Fastening and Leveling Drilling Template on Hole C1 & Bushing C2 with Wedge
Anchors 44
Figure 48: Drilling Third Hole Through Bushing C3 for Wedge Anchor............................... 45
Figure 49: Installing the Affinity Tilt Logger with ¼" Wedge Anchors, Washers & Nuts ...... 46
Figure 50: Installing the Affinity Tilt Logger with ¼" Wedge Anchors and Spherical Washer
Set
Figure 51: Angle Bracket Mounted Affinity Tilt Logger Installed in Horizontal Orientation Using
¼" Wedge Anchors ..................................................................................... 48
Figure 52: ¼" x 1" Long Drop-In Anchors, ¼" x 5/8" Long Hex Bolts and ¼" Flat Washers 49
Figure 53: Drilling Template Hole Set D Corresponding to Affinity Tilt Logger Angle Bracket
Mounting Holes for ¼" Drop-In Anchor ....................................................... 50
Figure 54: Masking Tape on 3/8" Concrete Drill Bits for Holes D1, D2 & D3 for ¼" x 1" long
Drop-In Anchors ......................................................................................... 50
Figure 55: Setting Tool to set the ¼" x 1" long Drop-In Anchor inside concrete .................. 51
Figure 56: Leveling and Fastening Drilling Template on Hole D1 with ¼" Drop-In Anchor, Hex
Bolt and Washer ......................................................................................... 51
Figure 57: Drilling Second Hole Through Bushing D2 for Drop-In Anchor .......................... 52
Figure 58: Leveling and Fastening Drilling Template on Hole D1 & Bushing D2 with ¼" Drop-
In Anchors, Hex Bolts and Washers ........................................................... 53
Figure 59: Drilling Third Hole Through Bushing D3 for Drop-In Anchor .............................. 53
Figure 60: Installing the Affinity Tilt Logger with ¼" Drop-In Anchors, Hex Bolts and Washers
54
Figure 61: Angle Bracket Mounted Affinity Tilt Logger Installed in Horizontal Orientation Using
¼" Drop-In Anchors .................................................................................... 55
Figure 62: Assembling Angle Bracket onto Affinity Tilt Logger ........................................... 56
Figure 63: Installing Affinity Tilt Logger using 2" U-Bolts and ¼" Hex Nuts and Washers ... 57
Figure 64: Installing the Affinity Tilt Logger with Gear Clamps through the Inner Slots of the
Angle Bracket ............................................................................................. 58
Figure 65: Installing the Affinity Tilt Logger with Gear Clamps through the Outer Slots of the
Angle Bracket ............................................................................................. 59
Figure 66: Installing Steel Cup Enclosed Magnets onto the Affinity Tilt Logger .................. 60
Figure 67: Installing Affinity Tilt Logger onto Steel Surface ................................................ 61
Figure 68: Direct Mounted Affinity Tilt Logger Installed in Vertical Orientation using Magnets
61
Figure 69: Direct Mounted Affinity Tilt Logger Installed in Horizontal Orientation using
Magnets ..................................................................................................... 62
Figure 70: Installing Steel Cup Encased Magnets onto the Angle Bracket ......................... 63
Figure 71: Installing Angle Bracket Mounted Affinity Tilt Logger onto Steel Surface .......... 64
Figure 72: Angle Bracket Mounted Affinity Tilt Logger installed at Horizontal Orientation using
Magnets ..................................................................................................... 64
Figure 73: Navigating to the Network Connection Menu .................................................... 65
Figure 74: Check Signal Strength Between the Affinity Tilt Logger and Gateway ............... 66
Figure 75: X, Y, and Z Axial Orientation for RSTAR Affinity Tilt Logger .............................. 73
PSM0005A
Released: 23 Jan 2025
47
RST Instruments Ltd.
RSTAR Affinity Tilt Logger
Installation and User Manual
Page 4