RST Instruments RSTAR Affinity Installation And User Manual page 4

Figure 20: Masking Tape on ¼" Concrete Drill Bits for Holes A1, A2 & A3 for ¼" x 2-¼" long
Wedge Anchors .......................................................................................... 27
Figure 21: ¼" x 2-1/4" long Wedge Anchor threads protruding out of concrete .................. 28
Figure 22: Leveling and Fastening Drilling Template on Hole A1 with ¼" Wedge Anchor, Nut
and Washer ................................................................................................ 29
Figure 23: Drilling Second Hole Through Bushing A2 for Wedge Anchor ........................... 29
Figure 24: Fastening and Leveling Drilling Template on Hole A1 & Bushing A2 with Wedge
Anchors 30
Figure 25: Drilling Third Hole Through Bushing A3 for Wedge Anchor ............................... 30
Figure 26: Installing the Affinity Tilt Logger with ¼" Wedge Anchors, Washers and Nuts ... 31
Figure 27: Installing the Affinity Tilt Logger with ¼" Wedge Anchors and Spherical Washer
set
Figure 28: Direct Mounted Affinity Tilt Logger installed at Horizontal Orientation using ¼"
Wedge Anchors .......................................................................................... 32
Figure 29: Direct Mounted Affinity Tilt Logger installed at Vertical Orientation using ¼" Wedge
Anchors 33
Figure 30: ¼" x 1" long Drop-In Anchors, ¼" x 5/8" Long Hex Bolts and ¼" Flat Washers . 33
Figure 31: Drilling Template Hole Set B Corresponding to Affinity Tilt Logger Base Plate
Mounting Slots for ¼" Drop-In Anchors ....................................................... 34
Figure 32: Masking Tape on 3/8" Concrete Drill Bits for Holes B1, B2 & B3 for ¼" x 1" long
Drop-In Anchors ......................................................................................... 34
Figure 33: Setting Tool to set the ¼" x 1" long Drop-In Anchor inside concrete .................. 35
Figure 34: Leveling and Fastening Drilling Template on Hole B1 with ¼" Drop-In Anchor, Hex
Bolt and Washer ......................................................................................... 36
Figure 35: Drilling Second Hole Through Bushing B2 for Drop-In Anchor .......................... 36
Figure 36: Leveling and Fastening Drilling Template on Hole B1 & Bushing B2 with ¼" Drop-
In Anchors, Hex Bolts and Washers ........................................................... 37
Figure 37: Drilling Third Hole Through Bushing B3 for Drop-In Anchor .............................. 38
Figure 38: Installing the Affinity Tilt Logger with ¼" Drop-In Anchors, Hex Bolts and Washers
39
Figure 39: Direct Mounted Affinity Tilt Logger Installed in Horizontal Orientation Using ¼"
Drop-In Anchors ......................................................................................... 39
Figure 40: Direct Mounted Affinity Tilt Logger Installed in Vertical Orientation Using ¼" Drop-
In Anchors .................................................................................................. 40
Figure 41: ¼" x 2-¼" Long Wedge Anchors, ¼" Flat Washers and ¼" Hex Nut .................. 41
Figure 42: Drilling Template Hole Set C Corresponding to Tilt Logger Angle Bracket Mounting
Holes for ¼" Studded Wedge Anchor ......................................................... 41
Figure 43: Masking Tape on ¼" Concrete Drill Bits for Holes C1, C2 & C3 for ¼" x 2-¼" long
Wedge Anchor ............................................................................................ 42
Figure 44: ¼" x 2-1/4" Long Wedge Anchor Threads Protruding Out of Concrete .............. 43
Figure 45: Leveling and Fastening Drilling Template on Hole A1 with ¼" Wedge Anchor, Nut
and Washer ................................................................................................ 43
Figure 46: Drilling Second Hole Through Bushing C2 for Wedge Anchor ........................... 44
PSM0005A
Released: 23 Jan 2025
32
RST Instruments Ltd.
RSTAR Affinity Tilt Logger
Installation and User Manual
Page 3