Enclustra Mars AX3 User Manual page 24

List of Figures
1 Hardware Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Mars PM3 Base Board Assembly Drawing (Top View) . . . . . . . . . . . . . . . . . . . . . . .
3 Run Configurations Settings - Application Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4 Run Configurations Settings - Target Setup Tab . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Generate linker scripts settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6 Initialize Block RAM settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7 QSPI Flash Programming Settings in Vitis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8 QSPI Flash Programming Settings in Vivado - Adding the Memory Device . . . . . . . . . . 20
9 QSPI Flash Programming Settings in Vivado . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
List of Tables
2 FPGA Firmware I/O Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 UART Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Hardware Setup Step-By-Step Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5 FPGA Bitstream Generation Step-By-Step Guide . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6 Vitis Workspace Preparation Step-By-Step Guide . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7 Running an Application Step-By-Step Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8 Generating the Boot Image File Step-by-Step Guide . . . . . . . . . . . . . . . . . . . . . . . . 16
9 Preparing the Hardware for QSPI Flash Boot Mode Step-by-Step Guide . . . . . . . . . . . . 17
10 Programming the QSPI Flash for QSPI Flash Boot Mode Step-by-Step Guide . . . . . . . . . 19
11 Booting from the QSPI Flash Step-by-Step Guide . . . . . . . . . . . . . . . . . . . . . . . . . 21
References
[1] Vivado Design Suite User Guide, Embedded Processor Hardware Design, UG898, Xilinx, 2020
[2] Vivado Design Suite Tutorial Embedded Processor Hardware Design, UG940, Xilinx, 2020
[3] Mars AX3 FPGA Module User Manual
Ask Enclustra for details
[4] Mars PM3 Base Board User Manual
Ask Enclustra for details
[5] Enclustra Module Configuration Tool (MCT)
https://www.enclustra.com/en/products/tools/module-configuration-tool/
[6] FTDI FT_PROG Utility
https://ftdichip.com/utilities/#ft_prog
[7] Enclustra Build Environment
https://github.com/enclustra-bsp/bsp-Xilinx
[8] Enclustra I2C Application Note
https://github.com/enclustra/I2CAppNote
[9] Enclustra Gigabit Ethernet Application Note
https://github.com/enclustra/GigabitEthernetAppNote
[10] Enclustra Modules Heat Sink Application Note
Ask Enclustra for details
D-0000-492-002 24 / 24 Version 2022.1_v1.0.2, 04.01.2023
5
9
6
7