Pos : 2 /D okumentati on allgemein/Ei nband/Ei nband H andbuch - Dec kbl att ohne Variantenfel d (Standar d) @ 9\mod_1285229289866_0.doc x @ 64941 @ @ 1
Manual
WAGO WINSTA® 770
WINSTA® Sunblind Box 4 Channel
770-629/130-000
Version 1.2.0, valid from HW/FW version XXXX0201XX
Pos : 3 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Hinweise z ur Dokumentation/Impressum für Standardhandbüc her - allg. Angaben, Ansc hriften, T elefonnummer n und E-Mail-Adres sen @ 3\mod_1219151118203_21.doc x @ 21060 @ @ 1
Fieldbus independent i/o modules for wago-i/o-system 750 (14 pages)
Summary of Contents for WAGO WINSTA 770
Page 1
Pos : 2 /D okumentati on allgemein/Ei nband/Ei nband H andbuch - Dec kbl att ohne Variantenfel d (Standar d) @ 9\mod_1285229289866_0.doc x @ 64941 @ @ 1 Manual WAGO WINSTA® 770 WINSTA® Sunblind Box 4 Channel 770-629/130-000 Version 1.2.0, valid from HW/FW version XXXX0201XX...
WAGO WINSTA® 770 Table of Contents 770-629/130-000 WINSTA® Sunblind Box 4 Channel Pos : 5 /D okumentati on allgemein/Verzeic hnisseInhalts verzeic hnis - Ü bers chrift oG und Verzeic hnis @ 3\mod_1219151230875_21.doc x @ 21063 @ @ 1 Table of Contents Notes about this Documentation ..............
Page 4
Table of Contents WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel Connection Examples ................29 6.1.1 Central Connection with 24V Signals (Central Operation) ....29 6.1.1.1 Central Operation without Line Break Monitoring ....... 29 6.1.1.2 Central Operation with Line Break Monitoring ......30 6.1.2...
Reproduction, translation, electronic and phototechnical filing/archiving (e.g., photocopying) as well as any amendments require the written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany. Non-observance will involve the right to assert damage claims. Pos : 11.2 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1 Manual Version 1.2.0, valid from HW/FW version XXXX0201XX...
Notes about this Documentation WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel Pos : 11.3 /All e Seri en ( Allgemei ne Module)/Ü bers chriften für alle Serien/Hinweis z ur D okumentati on/Symbole - Ü berschrift 2 @ 13\mod_1351068042408_21.doc x @ 105270 @ 2 @ 1 Symbols Pos : 11.4.1 /All e Serien ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und sons tige Hinweis e/Gefahr/Gefahr: _War nung vor Personenschäden allgemei n_ - Erl äuter ung @ 13\mod_1343309450020_21.doc x @ 101029 @ @ 1...
Page 7
WAGO WINSTA® 770 Notes about this Documentation 770-629/130-000 WINSTA® Sunblind Box 4 Channel Additional Information: Refers to additional information which is not an integral part of this documentation (e.g., the Internet). Pos : 11.5 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1 Manual Version 1.2.0, valid from HW/FW version XXXX0201XX...
Notes about this Documentation WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel Pos : 11.6 /All e Seri en ( Allgemei ne Module)/Hi nweis e zur D okumentati on/Zahlens ysteme @ 3\mod_1221059454015_21.doc x @ 21711 @ 2 @ 1...
2.1.1 Subject to Changes WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any alterations or modifications that serve to increase the efficiency of technical progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from the granting of patents or from the legal protection of utility patents.
Important Notes WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel Pos : 14.6 /All e Seri en ( Allgemei ne Module)/Ü bers chriften für alle Serien/Wichtige Erläuter ungenSic her hei tshi nweis e - Übersc hrift 2 @ 6\mod_1260180299987_21.doc x @ 46724 @ 2 @ 1 Safety Advice (Precautions) Pos : 14.7 /All e Seri en ( Allgemei ne Dokumente) ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits hi nweis e/Einl eitung Sicherheits hinweis e H ardware @ 6\mod_1260180170493_21.doc x @ 46720 @ @ 1...
Page 11
WAGO WINSTA® 770 Important Notes 770-629/130-000 WINSTA® Sunblind Box 4 Channel Avoid electrostatic discharge! The devices are equipped with electronic components that you may destroy by electrostatic discharge when you touch. Pay attention while handling the devices to good grounding of the environment (persons, job and packing).
Device Description WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel 3.3.2 230V Supply As a system supply (electrical supply for both the motors as well as the control electronics), the sunblind box needs 230 V alternating voltage. The power supply is handled by the three-pole plug connector with the designation "230 V."...
"Putting into operation > Setting bus or central operation." In bus operation, a WAGO-I/O controller can be used on a bus segment to connect up to 16 participants. These can be grouped and activated at will. The bus connection is made using the four-pole plug ("Bus/central") and the plug...
N.C. Down N.C. Figure 8: Bus/central connection Activation via the WAGO-I/O-SYSTEM 750 The following module is required to activate via bus signal/RS-485 and WAGO- I/O-SYSTEM: RS-485 serial interface, adjustable; item number 750-653/003-000. Manual Version 1.2.0, valid from HW/FW version XXXX0201XX...
The WAGO-I/O-SYSTEM is suitable for the screening connection system. Pos : 27 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1 Manual Version 1.2.0, valid from HW/FW version XXXX0201XX...
WAGO WINSTA® 770 Device Description 770-629/130-000 WINSTA® Sunblind Box 4 Channel 3.5.2 IDC Connectors for Jumper The sunblind box has an IDC connector for a jumper bridge, with which it is possible to select whether the box should be activated via a bus signal (RS-485) or via a 24V signal (central operation).
WAGO WINSTA® 770 Device Description 770-629/130-000 WINSTA® Sunblind Box 4 Channel 3.6.4 Inputs Table 12: Technical data: Inputs Number of inputs 4 switch inputs for local buttons Signal voltage 12 V DC Transmission medium Control line: J-Y (St) Y 2 x 2 x 0.6 mm max.
Device Description WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel 3.6.6 Control Table 14: Technical data: Control Mode Bus control or central control via 24VDC signal Connection type Socket without strain relief housing, 4-pole (Item No. 770-244) Strain relief housing, 4-pole (Item No.
The WINSTA sunblind boxes are connected to a serial bus (serial interface RS- 485, 750-653/003-000) via which the WAGO-I/O-SYSTEM as the superior controller can access up to 16 boxes per bus segment. This operating mode addresses both individual channels and groups of boxes.
WAGO WINSTA® 770 Function Description 770-629/130-000 WINSTA® Sunblind Box 4 Channel Operating Functions The sunblind box is equipped at the factory with various operating functions. The description of the necessary settings is found in Chapter "Putting into operation > Setting bus address and operating mode."...
Connect Devices WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel 6.1.1.2 Central Operation with Line Break Monitoring On principle, the configuration of a central operation (e.g. central switch, timer) should take place according to the following scheme. Figure 12: Wiring of the Winsta sunblind boxes with monitoring In central operation with line break monitoring, 0V levels are evaluated as a control signal.
The bus must be connected at the beginning and end to a 120 Ω resistor! Operation via bus signal/RS-485 The following module is required to operate via bus signal/RS-485 and WAGO I/O-System: WAGO I/O adjustable RS-485 module 750-653/003-000 Pos : 55 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1 Manual Version 1.2.0, valid from HW/FW version XXXX0201XX...
WAGO WINSTA® 770 Commissioning 770-629/130-000 WINSTA® Sunblind Box 4 Channel Setting Bus or Central Operation The sunblind box has an IDC connector for a jumper bridge, with which it is possible to select whether the box should be activated via a bus signal (RS-485) or via a 24V signal (central operation).
Commissioning WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel 7.3.2 Central Operation If the jumper bridge is plugged in the viewing direction of the figure above into the two upper pins, 24V activation is selected. Figure 16: Jumper setting for central operation...
WAGO WINSTA® 770 Commissioning 770-629/130-000 WINSTA® Sunblind Box 4 Channel Setting Bus Address and Operating Mode The sunblind box has two DIP switch modules with which you can set the bus address, the grouping of the motors, the moving time, and the moving logic.
Commissioning WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel 7.4.2 Setting Bus Address Setting of bus addresses only for bus operation Please note that the setting of bus addresses is only possible in bus operation. For Central operation, de-activate switches 1 to 5 of DIP Module 1 (address 0).
WAGO WINSTA® 770 Commissioning 770-629/130-000 WINSTA® Sunblind Box 4 Channel 7.4.3 Grouping Set the grouping with the switches 1, 2, and 3 of the DIP module 2. The drives are thus assigned via the plug connectors to the selected groups and local push buttons.
Commissioning WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel 7.4.3.4 Three Groups: Motors 1 and 2 Move Individually, Motors 3 and 4 Move Simultaneously To form three groups, Group A in which motor 1, Group B in which motor 2, and...
WAGO WINSTA® 770 Commissioning 770-629/130-000 WINSTA® Sunblind Box 4 Channel 7.4.4 Setting of Bus Failure Monitoring / Line Break Monitoring Activate/De-activate bus failure monitoring / line break monitoring using switch 4 of DIP Module 2. 7.4.4.1 Standard Mode Make the following settings to de-activate bus failure monitoring / line break...
Commissioning WAGO WINSTA® 770 770-629/130-000 WINSTA® Sunblind Box 4 Channel 7.4.5 Setting the Operating Time Set the operating time with switch 5 of the DIP module 2 to 1 minute or 4 minutes. 7.4.5.1 Operating Time 1 Minute In order to set an operating time of 1 minute, make the following settings:...
WAGO WINSTA® 770 Commissioning 770-629/130-000 WINSTA® Sunblind Box 4 Channel 7.4.6 Setting the Operating Function (Sunblind/Slat Function) Set the operating function with switch 6 of the DIP module 2 to sunblind or slat function. 7.4.6.1 Sunblind Function To select sunblind operation, make the following settings:...
Behavior after power failure in bus operation After a power failure, it can take up to 1 minute until the WAGO-I/O-SYSTEM has recorded the box again and it reacts to control commands. Pos : 58 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1 Manual Version 1.2.0, valid from HW/FW version XXXX0201XX...
Pos : 63 /Serie 770 ( WINSTA-Boxen) /Zubehör/Z ubehör 0770-0629/0130-0000 @ 7\mod_1268232006524_21.doc x @ 52253 @ @ 1 ® The following accessories are available for the WINSTA sunblind box 770- 629/130-000: Table 22: Accessories Description Item No. RS-485 serial interface for modular WAGO-I/O- 750-653/003-000 SYSTEM 750, freely-configurable ® Plug set for WINSTA sunblind box 770-5001/100-000 Includes: 1 x socket with strain relief housing, 3-pole (Item No.