Table of Contents
Advertisement
S T E P 8
Figure 14
6
6
Figure 15
8
8
7
7
STEP 16 - FLIP THE MACHINE ONTO ITS BACK.
USED CARBOARD OR A BLACNKET CAN BE
USED TO PROTECT THE ACHINE AND
8
8
7
7
6
6
FLOORS.
D
D
STEP 16 - FLIP THE MACHINE ONTO ITS BACK.
USED CARBOARD OR A BLACNKET CAN BE
USED TO PROTECT THE ACHINE AND
FLOORS.
D
D
C
C
C
C
B
B
B
B
A
A
A
A
Figure 16
8
8
7
7
6
6
8
8
7
7
10
Step 8 Hardware
5
5
4
4
6
6
5
5
4
4
5
5
4
4
3
3
Figure 17
5
5
4
4
3
3
6
6
5
5
4
4
Assemble Lower Seat
Figure 14: Locate the Step 8 Hardware Kit.
Position the Lower Seat into the slot in the
Seat Post on the Base.
TIP: Hold the seat slightly forward, then guide
it down in a backward diagonal direction.
When properly aligned, the round rod
(Actuator) that protrudes out of the Lower
Seat will need to rest inside of the mechanism
in the Seat Post slot.
Install 4 × Bolts and 4 × Washers and hand
tighten.
Figure 15: For ease of assembly, raise the Seat
to the max height by lifting on the Seat Height
Adjustment Lever and pulling up on the Seat.
Proceed to fully tighten all Bolts and Washers
3
3
with the 6 mm Allen Wrench.
3
3
2
2
1
1
2
2
1
1
D
D
Figure 16-17: Position the FreeStep to rest
on its back by lifting on the Console Support
D
D
Bar until the Seat Handles are resting on the
ground.
C
C
C
C
NOTE: Transport wheels will engage when
lifting the Console Support Bar. Use Caution
to avoid unintentional movement.
B
B
B
B
Use caution to avoid tipping and when
A
A
A
A
TOLERANCES
EXPECTATIONS LLC
EXPECTATIONS PROPRIETARY
FINISH:
.X
=
.1
UOS 63RMS ON
.XX
=
.03
BONNEY LAKE, WA 98391
TOLERANCES
EXPECTATIONS LLC
MACHINED
.XXX
=
.005
EXPECTATIONS PROPRIETARY
FINISH:
.X
=
.1
SURFACES OR
UOS 63RMS ON
THE INFORMATION CONTAINED HEREIN
AS PROCURED
ANGLE
=
1
.XX
=
.03
IS PROPRIETARY TO EXPECTATIONS AND
UNLESS NOTED
MACHINED
.XXX
=
.005
BONNEY LAKE, WA 98391
SHALL NOT BE REPRODUCED IN WHOLE
SURFACES OR
THE INFORMATION CONTAINED HEREIN
ANGLE
=
1
OR IN PART OR USED FOR ANY PURPOSE
PROJECT:
AS PROCURED
EXCEPT WHEN SUCH USER POSSESSES
FILLET RADII:
.005-.010
IS PROPRIETARY TO EXPECTATIONS AND
UNLESS NOTED
CORNER BREAK: .005-.010
SHALL NOT BE REPRODUCED IN WHOLE
DIRECT WRITTEN AUTHORIZATION
LT7
FROM EXPECTATIONS LLC
ALL DIMENSIONS IN INCHES
OR IN PART OR USED FOR ANY PURPOSE
PROJECT:
EXCEPT WHEN SUCH USER POSSESSES
FILLET RADII:
.005-.010
DRAWING
REV
DIRECT WRITTEN AUTHORIZATION
CORNER BREAK: .005-.010
LT7
UNLESS OTHERWISE NOTED
FROM EXPECTATIONS LLC
ALL DIMENSIONS IN INCHES
A
SURFACE ROUGHNESS PER ANSI B46.1
AI DRAWINGS
DIMENSIONING PER ASME Y14.5-2009
DRAWING
REV
DRAWN
WELD SYMBOLS PER AWS A2.4
D
UNLESS OTHERWISE NOTED
NICK SOLLER
SCALE: NONE
SIZE:
SHEET 17 OF 40
A
SURFACE ROUGHNESS PER ANSI B46.1
AI DRAWINGS
2
2
1
1
DIMENSIONING PER ASME Y14.5-2009
DRAWN
WELD SYMBOLS PER AWS A2.4
D
SCALE: NONE
SIZE:
SHEET 17 OF 40
NICK SOLLER
3
3
2
2
1
1
TOLERANCES
EXPECTATIONS LLC
FINISH:
EXPECTATIONS PROPRIETARY
.X
=
.1
UOS 63RMS ON
.XX
=
.03
MACHINED
BONNEY LAKE, WA 98391
.XXX
=
.005
SURFACES OR
THE INFORMATION CONTAINED HEREIN
ANGLE
=
1
AS PROCURED
UNLESS NOTED
IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
PROJECT:
FILLET RADII:
.005-.010
EXCEPT WHEN SUCH USER POSSESSES
CORNER BREAK: .005-.010
DIRECT WRITTEN AUTHORIZATION
LT7
FROM EXPECTATIONS LLC
ALL DIMENSIONS IN INCHES
DRAWING
UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1
AI DRAWINGS
DIMENSIONING PER ASME Y14.5-2009
DRAWN
WELD SYMBOLS PER AWS A2.4
D
NICK SOLLER
SCALE: NONE
SIZE:
2
2
1
1
CAUTION
!
lifting heavy objects.
D
D
C
C
B
B
A
A
REV
A
SHEET 14 OF 40
Advertisement
Table of Contents
