Table of Contents
Advertisement
S T E P 2
FIGURE 4
8
8
7
7
STEP 4.1 - FLIP THE MAHINE FORWARD AND
LET IT REST ON THE CONSOLE SUPPORT BAR.
IT IS RECCOMENDED TO USE SCRAP
8
8
7
7
CARDBOARD OR A BLANKET ON THE
D
D
FLOOR TO PROTECT THE FLOOR AND THE
STEP 4.1 - FLIP THE MAHINE FORWARD AND
MACHINE.
LET IT REST ON THE CONSOLE SUPPORT BAR.
IT IS RECCOMENDED TO USE SCRAP
CARDBOARD OR A BLANKET ON THE
D
D
FLOOR TO PROTECT THE FLOOR AND THE
MACHINE.
C
C
C
C
B
B
B
B
7
7
6
6
THE WOOD BLOCK
A
A
Figure 4
A
A
THE BASE. USE THE 6MM
TWO (2) M10X50 BOLTS
WOOD BLOCK, TWO
8
8
7
7
O (2) WASHERS. THIS
8
8
7
7
OR SHIPPING PURPOSES.
(1) M10X50 BOLT THAT
R LEVELING FOOT. THIS
CURE THE FLYWHEEL IN
DWARE AND BLOCK
WAY AT THE END OF
WILL NO LONGER BE
HT WANT TO HAVE THE
ONTO THEM FOR A LITTLE
LD REUSE THEM TO SHIP
EY NEEDED TO).
7
7
STABILIZER WITH
S AND WASHERS
HAVE BEEN
ED TO FULLY
OLTS WITH THE
Figure 6
7
7
6
6
Figure 7
6
6
6
5
5
4
4
6
6
5
5
4
4
3
3
5
5
Figure 5
6
6
5
5
4
4
3
3
6
6
5
5
4
4
6
6
5
5
5
5
3
3
2
2
1
1
2
2
1
1
D
D
D
D
Figures 4-5: Lift the rear Base and tilt the
FreeStep forward so the Console Support
Bar is resting on the ground.
C
C
C
C
B
B
B
B
Use caution to avoid tipping and when
4
4
3
3
A
A
A
A
TOLERANCES
EXPECTATIONS LLC
EXPECTATIONS PROPRIETARY
FINISH:
.X
=
.1
UOS 63RMS ON
MACHINED
.XX
=
.03
BONNEY LAKE, WA 98391
.XXX
=
.005
THE INFORMATION CONTAINED HEREIN
SURFACES OR
ANGLE
=
1
TOLERANCES
IS PROPRIETARY TO EXPECTATIONS AND
AS PROCURED
UNLESS NOTED
FINISH:
EXPECTATIONS LLC
EXPECTATIONS PROPRIETARY
UOS 63RMS ON
.X
=
.1
SHALL NOT BE REPRODUCED IN WHOLE
.XX
=
.03
OR IN PART OR USED FOR ANY PURPOSE
PROJECT:
MACHINED
.XXX
=
.005
BONNEY LAKE, WA 98391
EXCEPT WHEN SUCH USER POSSESSES
FILLET RADII:
.005-.010
SURFACES OR
DIRECT WRITTEN AUTHORIZATION
CORNER BREAK: .005-.010
THE INFORMATION CONTAINED HEREIN
LT7
ANGLE
=
1
FROM EXPECTATIONS LLC
ALL DIMENSIONS IN INCHES
IS PROPRIETARY TO EXPECTATIONS AND
AS PROCURED
UNLESS NOTED
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
DRAWING
REV
PROJECT:
UNLESS OTHERWISE NOTED
EXCEPT WHEN SUCH USER POSSESSES
FILLET RADII:
.005-.010
SURFACE ROUGHNESS PER ANSI B46.1
A
DIRECT WRITTEN AUTHORIZATION
AI DRAWINGS
CORNER BREAK: .005-.010
LT7
DIMENSIONING PER ASME Y14.5-2009
DRAWN
FROM EXPECTATIONS LLC
ALL DIMENSIONS IN INCHES
WELD SYMBOLS PER AWS A2.4
D
NICK SOLLER
SCALE: NONE
SIZE:
SHEET 4 OF 40
DRAWING
REV
2
2
UNLESS OTHERWISE NOTED
1
1
A
SURFACE ROUGHNESS PER ANSI B46.1
AI DRAWINGS
DIMENSIONING PER ASME Y14.5-2009
DRAWN
WELD SYMBOLS PER AWS A2.4
D
NICK SOLLER
SCALE: NONE
SIZE:
SHEET 4 OF 40
3
3
2
2
1
1
Figure 6: Use the 6 mm Allen Wrench to
remove the 2 × Bolts and 2 × Washers from
the wood block on the Base.
Use the 6 mm Allen Wrench to remove the
1 × Bolt from the Base.
4
4
NOTE: Discard wood block and hardware.
They are for shipping purposes only and are
not needed for use of the FreeStep.
Assemble Rear Stabilizer
Figure 7: Use the Step 2 Hardware Kit to
attach the Rear Stabilizer.
Align the Rear Stabilizer with the rear of
4
4
3
3
the Base and hand tighten 2 × Bolts and 2 ×
Washers.
Proceed to fully tighten each Bolt with the
6 mm Allen Wrench.
Once the Rear Stabilizer is assembled, return
the FreeStep to the upright position by lifting
up on the Console Support Bar until the Rear
Stabilizer is resting on the ground.
Step 2 Hardware
CAUTION
!
lifting heavy objects.
2
2
1
1
D
D
C
C
3
3
B
B
A
A
TOLERANCES
EXPECTATIONS LLC
FINISH:
EXPECTATIONS PROPRIETARY
.X
=
.1
UOS 63RMS ON
.XX
=
.03
MACHINED
PUYALLUP, WA 98391
.XXX
=
.005
SURFACES OR
THE INFORMATION CONTAINED HEREIN
ANGLE
=
1
AS PROCURED
IS PROPRIETARY TO EXPECTATIONS AND
UNLESS NOTED
SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE
PROJECT:
EXCEPT WHEN SUCH USER POSSESSES
FILLET RADII:
.005-.010
CORNER BREAK: .005-.010
DIRECT WRITTEN AUTHORIZATION
PROJECT NAME HERE
FROM EXPECTATIONS LLC
ALL DIMENSIONS IN INCHES
DRAWING
REV
UNLESS OTHERWISE NOTED
A
SURFACE ROUGHNESS PER ANSI B46.1
LT7_AI
DIMENSIONING PER ASME Y14.5-2009
DRAWN
WELD SYMBOLS PER AWS A2.4
D
SCALE: FULL SIZE:
SHEET 5 OF 40
NICK SOLLER
2
2
1
1
2
2
Advertisement
Table of Contents
