Teeter FreeStep LT7 Get Started page 11

S T E P 6
Assemble Leg Cover Sets
Figures 12a & b: Locate the Front Leg Cover
Sets, noting Right and Left markings. Pair each
set over the corresponding Right and Left
8 8
8 8 8 8
Upper Front Leg.
STEP 11 - INSTALL THE LEFT AND RIGHT LEG STEP 11 - INSTALL THE LEFT AND RIGHT LEG STEP 11 - INSTALL THE LEFT AND RIGHT LEG
COVERS WITH SIX (6) PHILLIPS SCREWS, COVERS WITH SIX (6) PHILLIPS SCREWS, COVERS WITH SIX (6) PHILLIPS SCREWS,
THREE (3) PER SIDE, USING THE PHILLIPS THREE (3) PER SIDE, USING THE PHILLIPS THREE (3) PER SIDE, USING THE PHILLIPS
SCREW DRIVER. TAKE CARE TO NOT PINCH
SCREW DRIVER. TAKE CARE TO NOT PINCH SCREW DRIVER. TAKE CARE TO NOT PINCH
TIP: To gain better access to the screw holes
D D D D D D
THE CONSOLE WIRE ON THE LEFT SIDE. THE CONSOLE WIRE ON THE LEFT SIDE.
THE CONSOLE WIRE ON THE LEFT SIDE.
NOTE, YOU MAY NEED TO MOVE THE NOTE, YOU MAY NEED TO MOVE THE NOTE, YOU MAY NEED TO MOVE THE
during assembly, carefully adjust the position
LINKAGE SOME TO GAIN ACCESS TO SOME LINKAGE SOME TO GAIN ACCESS TO SOME LINKAGE SOME TO GAIN ACCESS TO SOME
SCREW HOLES. SCREW HOLES. SCREW HOLES.
of the Linkage by pushing forward or pulling
USE HK2066. USE HK2066. USE HK2066.
backward.
Use the Step 6 Hardware Kit to attach the Leg
Cover Sets with 3 × Screws on each side and
C C
C C C C
fully tighten with the Phillips Screwdriver.
B B B B B B
S T E P 7
Assemble Handle Support Tubes
A A A A A A
Figure 13a & b: Locate the Handle Support
Tubes, noting Right and Left markings. Align
8 8 8 8 8 8
the Handle Support Tubes onto the top of the
Forward Pivot Arm.
Use the Step 7 Hardware Kit to attach the
Handle Support Tubes using 5 × Bolts on each
side and hand tighten.
Proceed to fully tighten all the Bolts with the
6 mm Allen Wrench.
7 7 6 6
7 7 7 7 6 6 6 6
7 7 7 7 7 7 6 6 6 6 6 6
STEP 11 - INSTALL THE LEFT AND RIGHT LEG
COVERS WITH SIX (6) PHILLIPS SCREWS,
THREE (3) PER SIDE, USING THE PHILLIPS
SCREW DRIVER. TAKE CARE TO NOT PINCH
D D
THE CONSOLE WIRE ON THE LEFT SIDE.
NOTE, YOU MAY NEED TO MOVE THE
LINKAGE SOME TO GAIN ACCESS TO SOME
SCREW HOLES.
USE HK2066.
C C
5 5 4 4
5 5 5 5 4 4 4 4
B B
A A
8 8
5 5 5 5 5 5 4 4 4 4 4 4
3 3 2 2
3 3 3 3 2 2 2 2
Step 6 Hardware
7 7 6 6
EXPECTATIONS PROPRIETARY EXPECTATIONS PROPRIETARY EXPECTATIONS PROPRIETARY
THE INFORMATION CONTAINED HEREIN THE INFORMATION CONTAINED HEREIN THE INFORMATION CONTAINED HEREIN
IS PROPRIETARY TO EXPECTATIONS AND
IS PROPRIETARY TO EXPECTATIONS AND IS PROPRIETARY TO EXPECTATIONS AND
SHALL NOT BE REPRODUCED IN WHOLE SHALL NOT BE REPRODUCED IN WHOLE SHALL NOT BE REPRODUCED IN WHOLE
OR IN PART OR USED FOR ANY PURPOSE OR IN PART OR USED FOR ANY PURPOSE
OR IN PART OR USED FOR ANY PURPOSE
EXCEPT WHEN SUCH USER POSSESSES EXCEPT WHEN SUCH USER POSSESSES EXCEPT WHEN SUCH USER POSSESSES
DIRECT WRITTEN AUTHORIZATION DIRECT WRITTEN AUTHORIZATION DIRECT WRITTEN AUTHORIZATION
FROM EXPECTATIONS LLC FROM EXPECTATIONS LLC FROM EXPECTATIONS LLC
UNLESS OTHERWISE NOTED UNLESS OTHERWISE NOTED UNLESS OTHERWISE NOTED
SURFACE ROUGHNESS PER ANSI B46.1 SURFACE ROUGHNESS PER ANSI B46.1 SURFACE ROUGHNESS PER ANSI B46.1
DIMENSIONING PER ASME Y14.5-2009 DIMENSIONING PER ASME Y14.5-2009
DIMENSIONING PER ASME Y14.5-2009
WELD SYMBOLS PER AWS A2.4 WELD SYMBOLS PER AWS A2.4 WELD SYMBOLS PER AWS A2.4
3 3 3 3 3 3 2 2 2 2 2 2
Step 7 Hardware
1 1
1 1 1 1
D D D D D D
Figure 12a
C C
C C C C
B B B B B B
Figure 12b 5 5
A A A A A A
TOLERANCES TOLERANCES TOLERANCES
FINISH: EXPECTATIONS LLC EXPECTATIONS LLC EXPECTATIONS LLC
FINISH: FINISH: .X = .1
.X .X = = .1 .1
UOS 63RMS ON UOS 63RMS ON UOS 63RMS ON
.XX .XX .XX = = = .03 .03 .03
MACHINED BONNEY LAKE, WA 98391 BONNEY LAKE, WA 98391 BONNEY LAKE, WA 98391
MACHINED MACHINED .XXX = .005
.XXX .XXX = = .005 .005
SURFACES OR SURFACES OR SURFACES OR
ANGLE ANGLE ANGLE = = = 1 1 1
AS PROCURED AS PROCURED
AS PROCURED UNLESS NOTED UNLESS NOTED
UNLESS NOTED
PROJECT: PROJECT: PROJECT:
FILLET RADII: FILLET RADII: FILLET RADII: .005-.010 .005-.010 .005-.010
CORNER BREAK: .005-.010 CORNER BREAK: .005-.010 CORNER BREAK: .005-.010 LT7 LT7
LT7
ALL DIMENSIONS IN INCHES
ALL DIMENSIONS IN INCHES ALL DIMENSIONS IN INCHES
DRAWING DRAWING DRAWING REV REV REV
A A A
AI DRAWINGS AI DRAWINGS
AI DRAWINGS
DRAWN DRAWN DRAWN
D D D
NICK SOLLER SCALE: NONE SCALE: NONE SCALE: NONE SIZE: SIZE: SIZE: SHEET 12 OF 40 SHEET 12 OF 40 SHEET 12 OF 40
NICK SOLLER NICK SOLLER
1 1 1 1 1 1
Figure 13a
Figure 13b
9