Table of contents 1 Welcome!.......................................... 5 What's in the box ....................................6 At a glance ......................................6 Compatible Barco system components..........................10 2 Installation and setup..................................11 Stand base plate mounting................................12 Single workstation setup................................12 Dual workstation setup with KVM switch ...........................14 QAWeb Enterprise registration ...............................17 VESA-mount installation ................................17...
Welcome! What's in the box ..........................6 At a glance.............................6 Compatible Barco system components...................10 R5915130 /05 Nio 2MP / 3MP LED Display...
• External power supply If you ordered a Barco MXRT display controller, it is also in the box together with its accessories. A dedicated user guide is available on the documentation disc. Keep your original packaging. It is designed for this display and is the ideal protection during transport and storage.
Page 7
Welcome! Presence sensor The presence sensor detects if somebody is present in front of the display (within a range of approximately 90 cm) and will set the backlight to a minimum if nobody is present after a time-out (configurable in the OSD menu). When a person is detected, the display will switch to normal operation again.
Page 8
Welcome! Image 1–2 Following connectors are available: DP IN 1 DP IN 2 DP OUT SERVICE DOWN UP 1 UP 2 DC IN Image 1–3 DisplayPort IN 1 (also main for KVM switching) DisplayPort IN 2 (also secondary for KVM switching) DisplayPort OUT (Manufacturing test only) Service (Service purpose only) USB-A 2.0 downstream connectors (3x)
Page 9
Welcome! Image 1–4 To adjust the height of the display, first move the slider at the back of the stand to the unlock position. Then you can raise or lower the display as desired. Image 1–5 Image 1–6 The height can be locked only in the lowest position, even though the slider at the back of the stand can be moved to the lock position at any height of the display.
Welcome! 1.3 Compatible Barco system components Overview Following Barco components are compatible with your Nio 2MP / 3MP LED Display LED Display: • QAWeb Enterprise Agent version 2.11 or later. • QAWeb Enterprise for DIN 6868-157-1.3.3 or later. • MXRT-x700 generation display controllers.
Installation and setup 2.1 Stand base plate mounting To mount the stand base plate Put the display face down on a clean and soft surface. Be careful not to damage the panel. Tip: The stand base plate can also be mounted while the display is still safely positioned in the bottom buffer of box.
Page 13
Connect the external DC power supply to a grounded power outlet by using one of the power cables included with the display. For a list of compatible display controllers, please refer to the compatibility matrix available on my.barco.com (MyBarco > My Support > Healthcare > Compatibility Matrices > Barco Systems Compatibility Matrices)
Your display will be running in a basic video mode at a default refresh rate when first time starting up. Install the MXRT driver and Intuitive Workflow Tools When using a Barco MXRT display controller, install the MXRT driver and Intuitive Workflow Tools on the connected workstation. Barco’s Intuitive Workflow Tools are designed to increase visibility of subtle details, improve focus during reading sessions, and accelerate workflow.
Page 15
Connect the external DC power supply to a grounded power outlet by using one of the power cables included with the display. For a list of compatible display controllers, please refer to the compatibility matrix available on my.barco.com (MyBarco > My Support > Healthcare > Compatibility Matrices > Barco Systems Compatibility Matrices)
Page 16
Your display will be running in a basic video mode at a default refresh rate when first time starting up. Install the MXRT driver and Intuitive Workflow Tools When using a Barco MXRT display controller, install the MXRT driver and Intuitive Workflow Tools on the connected workstation. Barco’s Intuitive Workflow Tools are designed to increase visibility of subtle details, improve focus during reading sessions, and accelerate workflow.
Learn more at www.barco.com/qaweb. To register your display system to your QAWeb Enterprise organization, the QAWeb Enterprise Agent must be installed and running on your workstation and it must be able to communicate with the QAWeb Enterprise cloud service.
Page 18
Installation and setup Image 2–6 2. Put the display face down on a clean and soft horizontal surface. Be careful not to damage the panel screen. 3. Push a flathead screwdriver into the right VESA mount cover hole to unlock the cover, then lift the cover with the flathead screwdriver.
Page 19
Installation and setup Image 2–9 6. Unscrew the 4 fixation screws while supporting the stand. Image 2–10 7. Attach the panel firmly to the VESA mount using 4 M4 screws. Respect the following rule to select an appropriate screw length: •...
Page 20
Installation and setup R5915130 /05 Nio 2MP / 3MP LED Display...
LCD displays use technology based on pixels. As a normal tolerance in the manufacturing of the LCD, a limited number of these pixels may remain either dark or permanently lit, without affecting the diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels.
Daily operation • “KVM input switching”, page 23 • “OSD menu access and use”, page 24 Image 3–1 To activate a shortcut bar function 1. During normal operation, press or turn the jog dial. The shortcut bar is activated. 2. Turn the jog dial left or right to select a function. 3.
Daily operation 3.5 OSD menu access and use About the OSD menu The OSD menu allows you to configure different settings to make your Nio 2MP / 3MP LED Display fit your needs within your working environment. Also, you can retrieve general information about your display and its current configuration settings through the OSD menu.
Advanced operation 4.1 OSD menu language About OSD menu language By default, the OSD menu comes up in English. However, there’s a wide range of other languages available for the OSD menu of your Nio 2MP/3MP LED Display. To change the OSD menu language Bring up the OSD main menu.
By default, DPMS mode is enabled on your display, but it also needs to be activated on your workstation. To do this, go to the “Power options” of your workstation. Barco recommends setting DPMS on your workstation to activate after 30 minutes of non-usage. When DPMS mode is enabled, three additional functions become available: hibernate, presence sensor and dry mode.
Advanced operation 4.7 Hibernate About hibernate When hibernate is enabled, not only the backlight, but also other functions will be disabled to reduce power consumption to a minimum. This happens after an adjustable time-out. DPMS mode must be enabled before hibernate can be enabled. See “DPMS mode”, page When DPMS mode with USB charging is enabled (see “DPMS mode”, page...
Advanced operation Enter the Presence Sensor(PS) submenu. Select Enabled/Disabled as desired and confirm. To adjust the presence sensor timer Bring up the OSD main menu. Navigate to the Power Management menu. Enter the PS Timer submenu. Set the presence sensor timer value as desired and confirm. 4.9 Dry mode About dry mode Dry mode prevents condensation from forming in the display.
Advanced operation 4.11 Color temperature/white tint About color temperature/white tint The available color temperature/white tint settings for your display are: • Native White: The native, unmodified color temperature of the LCD panel • Clear base: Simulation of the clearbase film color temperature •...
DICOM: DICOM (Digital Imaging and Communications in Medicine) is an international standard that was developed to improve the quality and communication of digital images in radiology. In short, the DICOM display function results in more visible grayscales in the images. Barco recommends selecting the DICOM display function for most medical viewing applications.
Embedded QA is not a replacement for the Barco QAWeb Enterprise solution. Although Embedded QA is a reliable option to perform a simple calibration or compliance test, Barco still highly recommends QAWeb Enterprise as the solution of choice for calibration and QA. QAWeb Enterprise...
Advanced operation displays from the moment it is installed and running. QAWeb Enterprise Agent will take over from Embedded QA and overwrite any settings which were applied by Embedded QA. 4.15.1 DICOM status report About DICOM status report • DICOM Compliance status: Shows if the current DICOM curve is compliant or not. •...
Advanced operation Select DICOM Calibration to start the calibration. Warning: Press and hold the jog dial for approximately 3 seconds during calibration will abort the calibration, previous values will be restored. Note: After calibration, the compliance check will start automatically. 4.15.4 DICOM error threshold About DICOM error threshold The threshold to define the DICOM compliance can be modified in steps of 5% starting from 5 to 30%.
Advanced operation 4.17 KVM switch About KVM switch The Nio 2MP / 3MP LED Display can be used in dual workstation setup with KVM switch. This allows the display to be connected to two different workstations and control both with a single keyboard and mouse connected to the display.
Advanced operation Navigate to the Image Settings menu. Enter the Grayscale Conversion submenu. Select a desired color conversion mode and confirm. 4.19 System info About system info Your display serial number, native resolution, firmware version, etc. are available in a dedicated submenu of the OSD menu.
Cleaning the display 5.1 Cleaning instructions To clean the display Apply a cleaning/disinfecting product to a soft lint-free cloth, such as a microfiber or gauze and rub the display surface thoroughly. In order to be effective, all surfaces must be cleaned for a certain amount of time (ranging from 30 seconds to 2 minutes).
Repackaging instructions 6.1 Repackaging instructions Overview of the packaging Image 6–1 1. Cables for mains, video and USB 2. Display controller box R5915130 /05 Nio 2MP / 3MP LED Display...
Page 41
Repackaging instructions 3. System CD('s) and user guide 4. External power supply 5. Top buffer 6. Display 7. Cardboard 8. Bottom buffer 9. Box 10. Stand base plate 11. Buffer box To repack your display 1. Place the empty box on a stable surface. 2.
Page 42
Repackaging instructions Image 6–3 7. Remove the stand base plate from the pillar by unscrewing the dedicated nut as shown below: Image 6–4 8. Adjust the position of the display so that it fits perfectly with the box. R5915130 /05 Nio 2MP / 3MP LED Display...
Page 43
Repackaging instructions Image 6–5 9. Place the removed stand base plate on the buffer box. 10. Place the top buffer on top of the display and stand base plate. 11. Place the accessories and all cables in the dedicated cavities of the top buffer. 12.
Important information 7.1 Safety information General recommendations Read the safety and operating instructions before operating the device. Retain safety and operating instructions for future reference. Adhere to all warnings on the device and in the operating instructions manual. Follow all instructions for operation and use. Electrical Shock or Fire Hazard To prevent electric shock or fire hazard, do not remove cover.
Page 47
Important information • The installer shall assess the magnetic environment before installation or use of the device. Power cords • Do not overload wall outlets and extension cords as this may result in fire or electric shock. • Mains lead protection (U.S.: Power cord): Power cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them, paying particular attention to cords at plugs and receptacles.
Electronic Products ” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of toxic substances in Electronic Information Products”.
Page 49
Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “General guidelines of environment-friendly use period of electronic information products” of Chinese Mainland.
The manufacturing country of the product is indicated on the product label (“Made in …”). Importers contact information To find your local importer, contact one of Barco’s regional offices via the contact information provided on our website (www.barco.com). FCC class B This device complies with Part 15 of the FCC Rules.
678 475 8000 Canadian notice CAN ICES-001(B) / NMB-001(B) Brazilian local representative Barco Ltda, Av. Ibirapuera, 2332 - Andar 8 - Bloco 2 - Conj 82, Bairro:Ibirapuera, Distrito:Moema, 4028-002, São Paulo, Brasil 7.5 EMC notice General information This device is for use in professional healthcare facility environments only.
Page 52
Important information Electromagnetic environment – Compliance Emissions test Guidance Voltage fluctuations/ flicker Complies connected to the public low-voltage emissions power supply network that supplies buildings used for domestic IEC 61000-3-3 purposes. This Nio 2MP / 3MP LED Display complies with appropriate medical EMC standards on emissions to, and interference from surrounding equipment.
Important information Electromagnetic Immunity test IEC 60601-1-2 test levels Compliance level environment – guidance typical location in a typical IEC 61000-4-8 commercial or hospital environment Conducted RF 3 Vrms (6 Vrms in ISM 3 Vrms (6 Vrms in ISM bands) bands) IEC 61000-4-6 150 kHz to 80 MHz...
Page 54
Important information Indicates the device meets the requirements of the applicable EC directives/ regulations. Indicates compliance with Part 15 of the FCC rules (Class A or Class B). Indicates the device is approved according to the UL regulations for Canada and US. E352529 Indicates the device is approved according to the UL Demko regulations.
Page 55
Important information Indicates the USB connectors on the device. Indicates the DisplayPort connectors on the device. Indicates the legal manufacturer. Indicates the manufacturing date. Indicates the entity importing the medical device into the locale. Indicates the temperature limitations for the device to safely operate within specs. Indicates that the device is a Medical Device.
Page 56
Important information Indicates this device must not be thrown in the trash but must be recycled, according to the European WEEE (Waste Electrical and Electronic Equipment) directive. Indicates Direct Current (DC). Indicates Alternating Current (AC). Stand-by Equipotentiality Protective earth (ground) Symbols on the box On the box of the device, you may find the following symbols (nonrestrictive list): Indicates a device that can be broken or damaged if not handled carefully when being...
Barco software products are the property of Barco. They are distributed under copyright by Barco NV or Barco Inc., for use only under the specific terms of a software license agreement between Barco NV or Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any form, is authorized.
Barco whatsoever. You further acknowledge that any such additions, changes or modifications may impair the ability of Barco – at Barco’s sole discretion - to continue to provide service, warranties, software updates, fixes, maintenance, access or such similar abilities, without any recourse or claim towards Barco whatsoever.
Page 59
Important information Front sensor Yes, I-Guard Presence sensor Maximum luminance (panel 1000 cd/m² typical) DICOM calibrated luminance 600 cd/m² Contrast ratio 2000:1 Response time ((Tr + Tf)/2) 12 ms (gray-to-gray average) (typical) Housing color Black (RAL 9004) / White (RAL 9003) Video input signals 2x DisplayPort 1.4 USB ports...
Page 60
WEEE, Packaging Directive *Some of the listed certifications may still be pending. For the actual list of applicable certifications, please refer to the product page on www.barco. or see the certification marks on the product label of your display. Supplied accessories •...
Page 61
Important information Active screen size (H x V) 433 x 325 mm (17.1 x 12.8") Aspect ratio (H:V) Resolution 3MP (2048 x 1536 pixels) Pixel pitch 0.2115 mm Color imaging Gray imaging Bit depth 30 bit Viewing angle (H, V) 178°...
Page 62
WEEE, Packaging Directive *Some of the listed certifications may still be pending. For the actual list of applicable certifications, please refer to the product page on www.barco. or see the certification marks on the product label of your display. Supplied accessories •...
Page 63
Important information QA software QAWeb Enterprise Warranty 5 years, including 20000 hours backlight warranty Operating temperature 0 °C to 35 °C (20 °C to 30 °C within specs) Storage temperature -20 °C to 60 °C Operating humidity 8 % to 80 % (non-condensing) Storage humidity 5 % to 85 % (non-condensing) Operating pressure...
Page 64
Important information R5915130 /05 Nio 2MP / 3MP LED Display...
Need help?
Do you have a question about the Nio MDNC-3521 SNES and is the answer not in the manual?
Questions and answers