• USB cable If you ordered a Barco display controller, it's also in the box together with its accessories. A dedicated user guide is available on the documentation disc. Keep your original packaging. It is designed for this display and is the ideal protection during transport and storage.
Page 7
If insufficient USB resources are available on the PC, the USB cable may be left unattached and the display will communicate essential QC information using DDC on the video cable, albeit more slowly; USB peripherals will also be ignored. K5902121 /04 Nio 5MP LED...
2. You can now safely tilt, swivel, pivot, raise and lower the display as desired. For a list of compatible display controllers, please refer to the compatibility matrix available on my.barco.com (MyBarco > My Support > Healthcare > Compatibility Matrices > Barco Systems Compatibility Matrices)
2.3 Cable connections To connect the cables 1. Open the connector compartment. Do this by gently pushing the two lips on top of the cover, after which it can be removed from the display. K5902121 /04 Nio 5MP LED...
Page 12
5. Route all cables through the cable duct in the stand of your display. For better strain-relief and shielding of the cables, fix the cables with the cable straps at the inside of the connector compartment. K5902121 /04 Nio 5MP LED...
About When you are using a Barco MXRT display controller, you can start up your Nio 5MP LED display system and install the MXRT driver and Intuitive Workflow Tools . Barco’s Intuitive Workflow Tools are designed to increase visibility of subtle details, improve focus during reading sessions, and accelerate workflow.
Learn more at www.barco.com/qaweb. To register your display system to your QAWeb Enterprise organization, the QAWeb Enterprise Agent must be installed and running on your workstation and it must be able to communicate with the QAWeb Enterprise cloud service.
Page 15
4. Slide the plastic cover over the neck of the foot. Image 2–12 5. Remove the four screws fixing the foot while supporting the foot. Image 2–13 6. Attach the arm stand firmly to the panel using 4 screws M4 x 8 mm. K5902121 /04 Nio 5MP LED...
LCD displays use technology based on pixels. As a normal tolerance in the manufacturing of the LCD, a limited number of these pixels may remain either dark or permanently lit, without affecting the diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels.
How to bring up the OSD menus The OSD menu allows you to configure different settings to make your Nio 5MP LED fit your needs within your working environment. Also, you can retrieve general information about your display and its current configuration settings through the OSD menu.
Page 20
Daily operation Overview key icons Left, Right Menu Enter Cancel Standby (IEC 60417–5009) K5902121 /04 Nio 5MP LED...
Certain OSD menu settings can be centrally managed by QAWeb Enterprise. Manually changing these settings in the OSD menu is still possible but the changes will be overwritten at each sync with QAWeb Enterprise. The OSD menu can also be completely disabled by QAWeb Enterprise. K5902121 /04 Nio 5MP LED...
About the OSD menu language By default, the OSD menu comes up in English. However, there’s a wide range of other languages available for the OSD menu of your Nio 5MP LED. To change the language of the OSD menu: Bring up the OSD main menu.
About the power lock function By enabling the power lock function, the Nio 5MP LED is forced to remain switched on. This means that it can’t be switched to stand-by mode manually until the power lock function is disabled again.
4.8 Luminance target About the luminance target The luminance target of your Nio 5MP LED is adjustable over a predefined range. When you change the luminance target, the display will adjust its backlight to reach the target. To set the luminance target: Bring up the OSD main menu.
To quickly switch the viewing mode without having to enter the OSD menu, touch the left and right key at the same time during normal operation. The diagnostic mode should always be selected when the Nio 5MP LED is intended to be used in a diagnostic environment.
DICOM display function when Ambient Light Compensation (ALC) is enabled. Please refer to “Ambient Light Compensation (ALC)”, page 26 to enable ALC. The available reading rooms for your Nio 5MP LED are: • CR/DR/ MAMMO: Corresponds to light conditions in diagnostic reading rooms for computed radiology, digital radiology or mammography.
Embedded QA is not a replacement for the Barco QAWeb solution. Although Embedded QA is a reliable option to perform a simple calibration or compliance test, Barco still highly recommends QAWeb as the solution of choice for calibration and QA. QAWeb brings many benefits...
OK. To set the DICOM error threshold: Bring up the OSD main menu. Navigate to the Configuration > Calibration > Embedded QA menu. K5902121 /04 Nio 5MP LED...
Video encoding modes specify how the color and luminance information is encoded in the video signal. In consumer displays, this is usually done by a limited 8-bit encoding mechanism. Your Nio 5MP LED however, features 10-bit encoding enabling it to better match the DICOM defined grayscale range. Such an extensive range is necessary to comply with the guidelines set forward by the latest medical guidelines.
Automatic When selecting this option, your Nio 5MP LED will automatically assign the correct video encoding settings to the connected video input signals. To manually select a video encoding mode: Bring up the OSD main menu.
4.19 EDID format About EDID format Your Nio 5MP LED describes its capabilities to the display controller by means of display identification data. This data contains timings, display size, pixel mapping info, etc. and is needed to make sure that the video source can be correctly displayed.
Navigate to the Maximum Luminance demo submenu and confirm. The maximum luminance demo is activated. Press the jog dial to manually cancel the maximum luminance demo, or wait for 60 seconds after which the demo is automatically cancelled. K5902121 /04 Nio 5MP LED...
Repacking instructions WARNING: Before repacking the display, follow the instruction to replace the foot protection buffer to prevent damage to the display. K5902121 /04 Nio 5MP LED...
Turn the panel counterclockwise to put the panel in landscape orientation, see “Display position adjustment”, page 10. Place the connector compartment cover in the foot protection buffer. Slide the foot protection buffer over the foot of the display. Tilt the panel back to the foot. Image 5–1 K5902121 /04 Nio 5MP LED...
Do not use sharp objects such as paperclips or tweezers to avoid damage to the LCD. CAUTION: Do not apply or spray liquid directly to the display as excess liquid may cause damage to internal electronics. Instead, apply the liquid to a cleaning cloth. K5902121 /04 Nio 5MP LED...
• The installer shall assess the magnetic environment before installation or use of the device. Power cords • Do not overload wall outlets and extension cords as this may result in fire or electric shock. K5902121 /04 Nio 5MP LED...
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. K5902121 /04 Nio 5MP LED...
Page 42
Electronic Products ” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of toxic substances in Electronic Information Products”.
Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “General guidelines of environment-friendly use period of electronic information products” of Chinese Mainland.
Page 44
The manufacturing country of the product is indicated on the product label (“Made in …”). Importers contact information To find your local importer, contact one of Barco’s regional offices via the contact information provided on our website (www.barco.com). FCC class B This device complies with Part 15 of the FCC Rules.
Electromagnetic emissions The Nio 5MP LED is intended for use in the electromagnetic environment specified below. The customer or the user of the Nio 5MP LED should assure that it is used in such an environment.
Page 46
430 – 470 GMRS 460, FM ± 5 kHz FRS 460 deviation 1 kHz sine 704 – 787 LTE Band Pulse 13, 17 modulation 217 Hz Nio 5MP LED doesn’t contain susceptible components to magnetic fields K5902121 /04 Nio 5MP LED...
Indicates the device is approved according to the UL regulations Indicates the device is approved according to the UL regulations for Canada and US Indicates the device is approved according to the UL regulations for Canada and US E352529 K5902121 /04 Nio 5MP LED...
Page 48
IEC 60950-1 R-xxxxxxxx www.bis.gov.in Indicates the device is approved according to the INMETRO regulations. Indicates the USB connectors on the device. Indicates the DisplayPort connectors on the device. Indicates the legal manufacturer. Indicates the manufacturing date. K5902121 /04 Nio 5MP LED...
Page 49
European WEEE (Waste Electrical and Electronic Equipment) directive. Indicates Direct Current (DC). Indicates Alternating Current (AC). Stand-by Equipotentiality Protective earth (ground) Values for xx and yy can be found in the technical specifications paragraph. K5902121 /04 Nio 5MP LED...
Barco software products are the property of Barco. They are distributed under copyright by Barco NV or Barco Inc., for use only under the specific terms of a software license agreement between Barco NV or Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any form, is authorized.
Page 52
China Energy Label, EU RoHS, China RoHS, REACH, Canada Health, WEEE, Packaging Directive Supplied accessories User guide Documentation disc Video cable (1 x DisplayPort) USB 2.0 cable Mains cables (UK, European (CEBEC/KEMA), USA (UL/CSA; adaptor plug NEMA5-15P), Chinese (CCC)) K5902121 /04 Nio 5MP LED...
Barco whatsoever. You further acknowledge that any such additions, changes or modifications may impair the ability of Barco – at Barco’s sole discretion - to continue to provide service, warranties, software updates, fixes, maintenance, access or such similar abilities, without any recourse or claim towards Barco whatsoever.
Page 54
Important information K5902121 /04 Nio 5MP LED...