Barco Nio E-2621 Getting Started Manual
  1. Manuals
  2. Brands
  3. Barco Manuals
  4. Monitor
  5. Nio E-2621
  6. Getting started manual
Barco Nio E-2621 Getting Started Manual

Barco Nio E-2621 Getting Started Manual

Display systems
Hide thumbs Also See for Nio E-2621:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installer and User Manual
Nio display systems
Getting Started Manual
Supported displays:
E-2621, E-3620, MDNG-5121, MDNC-3120

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Nio E-2621 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Barco Nio E-2621

Summary of Contents for Barco Nio E-2621

  • Page 1 Nio display systems Getting Started Manual Supported displays: E-2621, E-3620, MDNG-5121, MDNC-3120...
  • Page 2 (This page intentionally left blank.) (This page intentionally left blank.) Nio display systems...
  • Page 3 - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems - without written permission of Barco © 2007 Barco N.V. All rights reserved. Nio display systems...
  • Page 4 (This page intentionally left blank.) Nio display systems...

  • Page 5: Table Of Contents

    Front view................... 18 Rear view of E-2621, E-3620, MDNG-5121 ....... 19 Rear view of MDNC 3120............20 Display controller installation ..........23 Installing your Barco display controller ..........24 Quick installation................ 26 Detailed installation ..............27 Display installation ..............31 Installation precautions..............
  • Page 6 Table of Contents General tips..................62 Warranty Statement ..............67 Nio display systems...

  • Page 7: Preface

    Preface Nio display systems...

  • Page 8: Important Notice

    Barco software products are the property of Barco. They are distributed under copyright by Barco N.V. or BarcoView, LLC., for use only under the specific terms of a software license agreement between Barco N.V. or BarcoView LLC.
  • Page 9 Cet appareil ISM est conforme à la norme NMB-001 du Canada. FCC Compliance Information (display controller) CLASS B: This Barco Graphics Controller complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
  • Page 10 The use of shielded cables for connection of the monitor to the graphics card is required to ensure compliance with FCC regula- tions. Changes or modifications to this unit not expressly approved by Barco could void the user’s authority to operate this equipment. Nio display systems...

  • Page 11: Environmental Information

    Environmental information Environmental information Disposal Information The lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of it as required by local ordinances or regulations. This equipment has required the extraction and use of natural resources for its production.

  • Page 12: Safety Instructions

    Safety Instructions Safety Instructions General Recommendations Read the safety and operating instructions before operating the display. Retain safety and operating instructions for future reference. Adhere to all warnings on the display and in the operating instructions manual. Follow all instructions for operation and use. Electrical shock Type of protection (electrical): Display with external power supply: Class I equipment...
  • Page 13 Safety Instructions Power cords: • Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 AWG min., rated 300 V min., provided with a hospital-grade type plug 5-15P configuration for 120V application, or 6-15P for 240V application. • Do not overload wall outlets and extension cords as this may result in fire or electric shock.
  • Page 14 Safety Instructions Switch on DPMS on display and PC: • The display DPMS setting can be switched on in the display’s Settings menu or in QAWeb Agent’s Configuration window (Display > Extended). • The PC DPMS setting can be switched on in the Windows XP Display control panel (Screen Saver tab >...

  • Page 15: Explanation Of Symbols

    Explanation of symbols Explanation of symbols Symbols on the display and / or power supply On the display or power supply, you may find the following symbols: Indicates compliance to the essential require- ments of the Directive 93/42/EEC Indicates the display is approved according to the UL regulations Indicates the display is approved according to the c-UL regulations...
  • Page 16 Explanation of symbols Consult the operating instructions Indicates this apparatus must not be thrown in the trash but must be recycled, according to the European WEEE (Waste Electrical and Electronic Equipment) directive Symbols used throughout the manual: Warning: Risk of Caution: Risk of injury to human damage to the...

  • Page 17: Introduction

    Introduction Nio display systems...

  • Page 18: Display Parts, Controls And Connectors

    Display parts, controls and connectors Display parts, controls and connectors Front view BAR CO Figure 1: Front side Power LED The LED is off when the display is disconnected from the power. The LED is also off when the LED function is disabled in the on- screen display (OSD).

  • Page 19: Rear View Of E-2621, E-3620, Mdng-5121

    Display parts, controls and connectors Rear view of E-2621, E-3620, MDNG-5121 Figure 2: Rear side Connector compartment cover To get access to the connectors, remove the cover by pulling down the 2 clips at the top of the cover. Tilt & swivel foot cover This cover is packed in a separate box when the display is shipped to the customer.

  • Page 20: Rear View Of Mdnc 3120

    Display parts, controls and connectors Connect the external power supply, delivered with the display, to this connector. Tilt & swivel foot clip The display is shipped with this clip in the foot to protect the tilt & swivel mechanism during transport. After unpacking, you should remove this clip.
  • Page 21 Display parts, controls and connectors Connect the external power supply, delivered with the display, to this connector. +5 Vdc, 0.25 A power output for accessories. DVI (digital) video input Slot for security cable (e.g., Kensington lock) USB upstream port Connect this connector to the PC USB bus if you wish to connect USB devices to the display’s USB downstream port.
  • Page 22 Display parts, controls and connectors (This page intentionally left blank.) Nio display systems...

  • Page 23: Display Controller Installation

    Display controller installation Nio display systems...

  • Page 24: Installing Your Barco Display Controller

    Installing your Barco display controller Installing your Barco display controller This chapter will guide you through the physical installation of the display controller(s) for your B Display System. ARCO CAUTION – Wear a grounded, protective ESD strap when handling or during installation of the display controller.
  • Page 25 Installing your Barco display controller Note: To use multiple B PCIe display controllers in a ARCO single host, you need to enable VGA on only ONE of the B ARCO PCIe display controllers and disable VGA on ALL the other BarcoMed display controllers.

  • Page 26: Quick Installation

    Installing your Barco display controller Quick installation Experienced users and system administrators can follow these brief instructions for installing the display controller(s) for your B ARCO Display System in the shortest possible time. To perform a quick installation CAUTION – Wear a grounded, protective ESD strap when handling or during installation of the display controller.

  • Page 27: Detailed Installation

    Installing your Barco display controller Detailed installation The following instructions will take you step by step through the installation of the display controller(s) for your B Display ARCO System. CAUTION – Wear a grounded, protective ESD strap when handling or during installation of the display controller.
  • Page 28 Installing your Barco display controller Align the display controller(s) for your B Display System ARCO with the slot(s) and press it(them) in firmly until the card(s) is(are) fully seated. Note: This step applies only to the MXRT 5100 and MXRT 7100.
  • Page 29 Installing your Barco display controller Connecting your Barco displays Figure 7: MXRT 2100 & B PCIe display controller Baseplate ARCO Head 1 – DVI-I Connection Head 2 – DVI-I Connection Figure 8: MXRT 5100 and MXRT 7100 Baseplate Head 1 – DVI-I Connection Stereographics Connection Note: This option is not supported in Nio Systems.
  • Page 30 If you have properly installed your graphics card, the Windows start-up messages will appear once the boot procedure is finished. Your Barco display(s) will be running in a basic video mode at a default refresh rate. Higher resolutions and refresh rates, such as 1536x2048@60Hz, are not avail- able at this stage of the installation.

  • Page 31: Display Installation

    Display installation Nio display systems...

  • Page 32: Installation Precautions

    Installation precautions Installation precautions Precautions • Keep your original packaging. It is designed for this display and is the ideal protection during transport. • Avoid reflections in the flat panel to reduce eye strain. • Place the display on a strong and stable table or desk. •...

  • Page 33: After Unpacking The Display

    After unpacking the display After unpacking the display Important: In the factory, the height-positioning system in the display foot is blocked with a red clip to prevent damage during transportation. Before installing the display, you must remove this clip. Clip Figure 9 To remove the clip: 1.
  • Page 34 After unpacking the display Adjust the panel orientation You can change the orientation of the panel at any time, but it is more convenient to select landscape or portrait orientation before connecting the cables. BAR CO BAR CO Figure 10: Figure 11: Portrait Landscape...
  • Page 35 After unpacking the display Figure 12: Tilt the panel before rotating To change from portrait to landscape, turn the panel counterclockwise. BAR CO Figure 13: To rotate the panel from portrait to landscape To change from landscape to portrait, turn clockwise. Nio display systems...
  • Page 36 After unpacking the display Adjust the panel orientation You can change the orientation of the panel at any time, but it is more convenient to select landscape or portrait orientation before connecting the cables. BAR CO BAR CO Figure 14: Portrait orientation Figure 15: Landscape orientation To change the panel orientation: Stand at the front side of the panel and take the panel at both...
  • Page 37 After unpacking the display To change from portrait to landscape, turn the panel counterclockwise. BAR CO Figure 17: To rotate the panel from portrait to landscape To change from landscape to portrait, turn clockwise. Note: If, after installing the display or the system, you change the panel orientation while an image is on the screen, the result depends on the graphic board and the resolution of the image.

  • Page 38: Connecting The Signal Cables

    Connecting the signal cables Connecting the signal cables To connect the signal cables to the display: To get access to the connectors, remove the connector compartment cover by pulling down the 2 clips at the top of the cover. The location of the connectors depends on the display type: Figure 18: Inputs E-2621, E-3620, MDNG-5121 Figure 19: Inputs MDNC-3120 •...

  • Page 39: Cable Routing

    Cable routing Cable routing Routing the signal cables • Bind the cables in the connector compartment together with the cable tie inside the connector compartment. • Put the connector compartment cover back on the display. Pay attention that the signal cables are positioned under the bulge in the cover.
  • Page 40 Cable routing Slide the cover upward while moving the lower side of the cover towards the foot. Press the cover to the foot so that it makes a clicking sound. Nio display systems...

  • Page 41: Vesa-Mount Installation

    Vesa-mount installation Vesa-mount installation The panel, standard attached to the tilt & swivel foot, is compatible with the VESA 100 mm standard. So it can be used with an arm stand according to the VESA 100 mm standard. Therefore, the tilt & swivel foot must be removed from the panel. Important: •...
  • Page 42 Vesa-mount installation 5. Lift up the round plastic cover. 6. Remove the four screws fixing the foot while supporting the foot. 7. Attach the arm stand firmly to the panel using 4 screws M4 x 8 mm. 4 screws M4 x 8mm Figure 22 Nio display systems...

  • Page 43: Cleaning Instructions

    Cleaning instructions Cleaning instructions Precautions • Take care not to damage or scratch the front filter or LCD panel. Be careful with rings or other jewelry that can touch the front filter. • Do not apply pressure on the front filter or LCD panel. •...

  • Page 44: Cabinet

    Cleaning instructions • Detergents with abrasives • Steel wool • Sponge with abrasives • Steel blades • Cloth with steel thread Cabinet Proceed as follows: • Clean the cabinet using a soft cotton cloth, lightly moistened with a recognized cleaning product for medical equipment. •...

  • Page 45: Software Installation

    Software installation Nio display systems...

  • Page 46: Installing Drivers And Software

    Installing drivers and software Installing drivers and software This chapter will guide you through the installation of the drivers, software and documentation associated with your B Display ARCO System or Nio display(s). Driver and software installation prerequisites Note: To install or remove the drivers, software, or documentation you must be logged on as a user with administrator privileges.
  • Page 47 Installation CD-ROM and double click on the file, Setup.exe. Click Next. Click Yes to accept the terms of the Barco and ATI license agreements. The Barco setup wizard will continue with the installation only if you accept the terms of both license agreements.
  • Page 48 Nio color displays. For more information about Color, Palette and Drawing modes please refer to the Barco Control Panel section of the Barco on-line User Manual. If you choose the Express option, you can modify the above driver settings through the Barco tab of the advanced options of the Windows Display Control Panel.
  • Page 49 Software should automatically detect your Barco displays and attach them to the desktop with the correct resolution. If the Barco Monitor Plug and Play Software fails to detect your Barco displays or fails to attach them to the desktop correctly please refer to the section, Setting the resolution of your Nio display on page 64 in the Troubleshooting section of this manual.
  • Page 50 To install the drivers and software silently, please follow the steps below: Insert the B Display System Installation CD-ROM into your ARCO CD/DVD drive. When the Barco Product Installation Wizard starts click “Cancel”. Click the Start button in the task bar. Click Run. Click Browse and...
  • Page 51 Installing drivers and software browse to the root directory of the location where you saved the contents of your B Display System ARCO Installation CD-ROM. Click on the file, Setup.exe, and click Open. In the Open address window, place your cursor at the end of the line of text that appears and add the following text after Setup.exe, a space and -silent.
  • Page 52 CD drive after the operating system has started. If your CD drive’s auto-run is not enabled or the Barco Product Installation Wizard does not start automatically, you can run the Barco Product Installation Wizard manually by following these steps: Click the Start button in the task bar.
  • Page 53 Software should automatically detect your Barco displays and attach them to the desktop with the correct resolution. If the Barco Monitor Plug and Play Software fails to detect your Barco displays or fails to attach them to the desktop correctly please refer to the section, Setting...
  • Page 54 51 of this manual. Uninstalling the drivers and software To uninstall the Barco drivers, software or documentation for your Nio display Systems, please use the Windows Add/Remove Programs utility. This can be found in the Windows Control Panel.
  • Page 55 Installing drivers and software browse to the root directory of the B Display System ARCO Installation CD-ROM. Click on the file, Setup.exe, and click Open. Browse to the root directory of the location where you saved the contents of your B Display System ARCO Installation CD-ROM.
  • Page 56 Installing drivers and software (This page intentionally left blank.) Nio display systems...

  • Page 57: Where To Get More Information

    Where to get more information Nio display systems...
  • Page 58 The online user guide is installed on the system PC during the system driver installation. To open the online user guide, select Start>Program Files>Barco>Documentation>Nio online user guide from the Windows Start menu. The online user guide uses Java scripts to create the html pages. In Windows XP, SP2, it is possible that Internet Explorer blocks them for security reasons.
  • Page 59 Where to get more information Nio display systems...
  • Page 60 Where to get more information (This page intentionally left blank.) Nio display systems...

  • Page 61: Troubleshooting

    Troubleshooting Nio display systems...

  • Page 62: General Tips

    General tips General tips • If one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or power supplies. In that way you can find out if the problem resides in the display or not. If the display screen remains black after installation: Possible causes: •...
  • Page 63 Display System you must be logged in using an account with administrator privileges. If you are using a color display in conjunction with your Barco grayscale display(s) or you have you should configure your desktop before setting the resolution of the your Barco grayscale display(s).
  • Page 64 Properties. Click on the Settings tab. Select the rectangle that represents the Barco Nio display whose settings you wish to change. Note: If you are using the VGA capabilities of your BarcoMed N display controller, the resolution for the first display may be set to a VGA resolution of “640 x 480”...
  • Page 65 General tips clicking on the rectangle that represents it, deselect Attached and click the Apply button. Note: Since Windows will not let you detach the primary display connected to a particular controller, you may need to temporarily make another display the primary display For the display which is still attached click Click on the Advanced Button.
  • Page 66 General tips If you are using a Quad-Head Configuration repeat all of the above steps for the two displays on the second display controller. Note: If you have a single display configuration and you have enabled DualView, Windows will not allow you to attach the second head.

  • Page 67: Warranty Statement

    Warranty Statement Nio display systems...
  • Page 68 Customer on how to proceed. Customer Support may ask to return the faulty equipment or faulty subassemblies to the Barco Customer Support Center (or an authorized service center) for repair activities. The Customer shall ask for a RMA or RAN number to a Barco Customer Support Center (or an authorized service center).
  • Page 69 If there is an indication that the equipment was used - even temporary - outside its specifications, Barco n.v. is entitled not to perform warranty repairs and terminate the warranty agreement. Any actions that have been taken by Barco n.v. in this respect, may be invoiced to the Customer at normal pricing.
  • Page 70 Warranty Statement (This page intentionally left blank.) Nio display systems...
  • Page 71 B410582-00 May 2007 www.barco.com...

This manual is also suitable for:

Nio e-3620Nio mdnc-3120Nio mdng-5121

Table of Contents