EWM Phoenix 301 Progress puls Operating Instructions Manual page 4

Contents
5.6.10
5.6.11
5.6.12
5.6.13
5.6.14
5.6.15
5.6.16
5.6.17
5.6.18
5.6.19
5.6.20
5.6.21
5.7 TIG welding ..................................................................................................................................78
5.7.1
5.7.2
5.7.3
5.7.4
5.7.5
5.7.6
5.7.7
5.8 MMA welding................................................................................................................................85
5.8.1
5.8.2
5.8.3
5.8.4
5.8.5
5.8.6
5.8.7
5.9 Shielding gas supply ....................................................................................................................88
5.9.1
5.9.2
5.9.3
5.9.4
5.10 Interfaces .....................................................................................................................................90
6 Maintenance, care and disposal .........................................................................................................91
6.1 General.........................................................................................................................................91
6.2 Maintenance work, intervals.........................................................................................................91
6.2.1
6.2.2
4
5.6.9.2 Operating point setting using material thickness, welding current, wire
speed.............................................................................................................39
5.6.9.3 Arc length correction setting..........................................................................39
5.6.9.4 Accessory components for operating point setting .......................................39
MIG/MAG welding data display ....................................................................................40
forceArc.........................................................................................................................41
rootArc ..........................................................................................................................41
MIG/MAG functional sequences / operating modes.....................................................42
5.6.13.1 Explanation of signs and functions................................................................42
MIG/MAG program sequence ("Program steps" mode) ...............................................55
5.6.14.1 Selection of the program sequence parameter .............................................55
5.6.14.2 MIG/MAG overview of parameters ................................................................56
5.6.14.3 Example, tack welding (non-latched) ............................................................57
5.6.14.4 Example, aluminium tack welding (non-latched special) ..............................57
5.6.14.5 Example, aluminium welding (latched special) .............................................58
5.6.14.6 Example, visible seams (latched super pulse) ..............................................59
5.6.14.7 Welding process changeover ........................................................................60
Main program A mode ..................................................................................................61
5.6.15.1 Selecting parameters (program A) ................................................................63
MIG/MAG automatic cut-out .........................................................................................63
Standard MIG/MAG torch .............................................................................................64
MIG/MAG special-torches.............................................................................................64
5.6.18.1 Program- and Up- / down operation..............................................................64
Remote control .............................................................................................................65
R10, R20, R40 ..............................................................................................................65
Advanced settings ........................................................................................................66
5.6.21.1 Selecting, changing and saving parameters .................................................66
5.6.21.2 Reset to factory settings................................................................................68
5.6.21.3 The special parameters in detail ...................................................................69
5.6.21.4 Switching between Push/Pull and intermediate drive ...................................77
Welding torch and workpiece line connection ..............................................................78
welding task selection...................................................................................................79
welding current setting..................................................................................................79
TIG arc ignition .............................................................................................................79
5.7.4.1 Liftarc ignition ................................................................................................79
Pulses, function sequences ..........................................................................................80
5.7.5.1 Explanation of signs and functions................................................................80
TIG automatic cut-out ...................................................................................................83
TIG program sequence ("Program steps" mode) .........................................................84
5.7.7.1 TIG parameter overview................................................................................84
Connecting the electrode holder and workpiece lead ..................................................85
welding task selection...................................................................................................86
welding current setting..................................................................................................86
Arcforce.........................................................................................................................86
Hotstart .........................................................................................................................87
Antistick.........................................................................................................................87
Parameter overview......................................................................................................87
Connecting the shielding gas supply ............................................................................88
Gas test ........................................................................................................................89
"Rinse tube package" function......................................................................................89
Setting the shielding gas quantity.................................................................................90
Daily maintenance tasks...............................................................................................91
Monthly maintenance tasks ..........................................................................................91
099-005023-EW501
09.08.2010