Wiring The Unit (120 Volt Power Supply) - Regency Fireplace Products City CP60E Series Owners & Installation Manual

installation
Wiring the Unit (120 Volt Power Supply) (Both Non Power Vent/Power Vent)
The wiring for the unit should be completed before any finishing material is installed.
All electrical wiring must be completed by a qualified electrician.
1. Remove the right access panel--see access panel removal instructions in this manual.
DETAIL A
SCALE 1 : 8
DETAIL A
Side A SCALE 1 : 8
2. Loosen 2 screws in locations shown below.
DETAIL D
SCALE 1 : 8
DETAIL D
SCALE 1 : 8
Side A
3. Slide electrical box plate towards the back of the unit and then out.
Side A
DETAIL E
SCALE 1 : 8
66
| City Series CP60E
3RD ANGLE TOLERANCES UNLESS
PROJECTION OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
UNITS IN INCHES ANGULAR = 1
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
3RD ANGLE TOLERANCES UNLESS
PROJECTION OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
UNITS IN INCHES ANGULAR = 1
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
3RD ANGLE TOLERANCES UNLESS
PROJECTION OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
UNITS IN INCHES ANGULAR = 1
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
DETAIL E
SCALE 1 : 8
3RD ANGLE TOLERANCES UNLESS
PROJECTION OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
UNITS IN INCHES ANGULAR =
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
3RD ANGLE
PROJECTION
DO NOT SCALE
DRAWING
UNITS IN INCHES
FIREPLACE PRODUCTS -
MAT'L :
INTERNATIONAL
SHEAR/ PUNCH/ FORM
PROCESS :
1:24 CP60 MAIN ASSEMBLY
SCALE: PART :
11/19/2021
PART NO:
DWN: DATE:
457-500
E.C.N.: SIGN: DATE:
-
FIREPLACE PRODUCTS
MAT'L :
INTERNATIONAL
SHEAR/ PUNCH/ FORM
PROCESS :
1:24 CP60 MAIN ASSEMBLY
SCALE: PART :
11/19/2021
PART NO:
DWN: DATE:
457-500
E.C.N.: DATE:
SIGN:
FIREPLACE PRODUCTS
MAT'L :
INTERNATIONAL
PROCESS :
1:24
SCALE: PART :
11/19/2021
DWN: DATE:
DATE:
E.C.N.: SIGN:
FIREPLACE PRODUCTS
INTERNATIONAL
1:24
SCALE:
DWN: DATE:
1
E.C.N.: SIGN:
TOLERANCES UNLESS
FIREPLACE PRODUCTS
OTHERWISE STATED
INTERNATIONAL
DIMENSIONS
0.000 = 0.01 CRITICAL
1:24
SCALE:
0.000 = SPECIFIED TOLERANCE
0.000 = 0.031
DWN:
0.000 REF = REFERENCE ONLY
ANGULAR = 1
E.C.N.:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
A
A
REV:
-
REV:
-
D
-
SHEAR/ PUNCH/ FORM
CP60 MAIN ASSEMBLY
PART NO: REV:
457-500
-
D
-
MAT'L :
SHEAR/ PUNCH/ FORM
PROCESS :
CP60 MAIN ASSEMBLY
PART :
11/19/2021
PART NO: REV:
457-500
-
DATE:
E
-
MAT'L :
SHEAR/ PUNCH/ FORM
PROCESS :
CP60 MAIN ASSEMBLY
PART :
11/19/2021
PART NO:
DATE:
457-500
SIGN: DATE:
REV:
-