Gate Disable; Partial Open - Maximum Controls MAX MEGATRON 1400HP Installation And Owner's Manual

gate disable

An ON/OFF switch or 7-Day timer devices can be connected to the GATE DISABLE
input. When these devices are turned ON, they will DISABLE normal opening
devices such as keypad, exit loop etc. The FIRE DEPT/ MAX OPEN and RADIO
inputs will remain enabled when GATE DISABLE has been turned ON. This is
useful when the gated area needs to be secured from ALL but emergency or
authorized vehicle entry. Some examples are: Residential home vacation period or
during closed hours of a business when no one can monitor the property.
When GATE DISABLE is turned ON: The operator will beep for 3 minutes
BEFORE arming itself. This allows time to turn ON GATE DISABLE and
leave the property before it is armed.
When FIRE DEPT/MAX OPEN gets activated: Gate opens and GATE TAMPER
relay will activate immediately.
When RADIO Input gets activated: Gate opens and GATE TAMPER relay will activate after 3 min. This allows time to turn OFF
GATE DISABLE or disarm an existing building alarm system if connected.
IMPORTANT: It is NOT recommended activating the GATE DISABLE device while persons are present inside the property.
p artial open
A gate can set to partially open by recording the PARTIAL OPEN gate cycle. LED will stay lit
when PARTIAL OPEN is ON.
IMPORTANT: Limit switches MUST be learned BEFORE Partial Open can be recorded.
RECORD
To

PARTIAL OPEN:

1. With gate in CLOSED position, press and release PARTIAL OPEN
button to START recording. Blue LED starts flashing.
2. Press 3-button station OPEN button to start gate's open cycle.
3. Press 3-button station STOP button when gate is in desired partial open position (Beyond center loop).
4. Press PARTIAL OPEN button AGAIN to STOP recording. Blue LED stops flashing,
open position has been recorded. LED remains ON.
ERASE
To PARTIAL OPEN recording:
Press and HOLD PARTIAL OPEN button for 5 sec. LED turns OFF.
NOTE: The FIRE DEPT and/or MAX
OPEN connected devices will always
FULLY open gates even when the
partial open is being used.
matrix 1
PARTIAL
OPEN
POSITION
RECORDER
CAUTION: Gates partial OPEN
position MUST be outside the
Center Loop when in-ground
loops have been installed.
MATRIX 1
MADE in USA
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI
TAILGATE
EXIT EXIT ON
CENTER CENTER
SAFETY
MIN IN
CLOSE TIMER
ID
PLUG
12VDC 12VDC
GND GND
24VDC
GND
O N
F
O F
7-Day
Enabled inputs when
ON/OFF
Timer
GATE DISABLE is turned ON.
Switch
MATRIX 1
MADE in USA
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI
TAILGATE
EXIT ON
CENTER
SAFETY
MIN
OFF
CLOSE TIMER
ID
MOTOR MOTION PLUG
12VDC
GND
24VDC 24VDC
GND GND
OPEN STOP CLOSE
CENTER LOOP
BATTERY PRIMARY
BACK-UP MODE GATE
LEAVE MAGLOCK
CLOSED
DELAY
LEAVE OPEN OPEN OPEN MAG
LEFT RIGHT
OPEN 1 TIME
OFF 1.5Sec 2Sec LOCK
COM
NC
Tamper NO
GATE
EXIT CENTER SAFETY COM
TAMPER
GND
OFF
Tamper IN
PHOTOCELL
EDGE 1
UL
MAX MAX
OFF OFF EDGE 2
ENTRAP
ER
ID PLUG
PARTIAL MOTOR MOTION ERROR
OPEN
UL ALARM 12V
ALARM RET
OPEN PEN STOP STOP CLOSE RESET
POSITION GND
RECORDER
MAX
REVERSE SENSITIVITY REVERSE SENSITIV
GATE SPEED
MOTOR OVERLOAD OTOR OVERLOAD
OBD PORT
OPEN
GATE
MIN
NO LIMIT SWITCH / WITCH / COM
STATUS ST
CLAMP SLIPPING PING
MAX
CLOSE
LIMIT BATTERY
SWITCH
IN USE
ON-LINE
POWER
NOTE: See page 46 for
more information about
this unique feature.
BATTERY PRIMARY
BACK-UP MODE GATE
LEAVE MAGLOCK
CLOSED
DELAY
OPEN OPEN
LEAVE OPEN MAG
OPEN 1 TIME LEFT RIGHT
OFF 1.5Sec 2Sec LOCK
COM
NC
Tamper NO
GATE
EXIT CENTER SAFETY
COM
TAMPER
GND
OFF
Tamper IN
PHOTOCELL
UL EDGE 1
MAX
ENTRAP EDGE 2
ID PLUG
PARTIAL MOTOR MOTION
ERROR
OPEN OPEN
UL ALARM 12V
ALARM RET
RESET
OPEN STOP CLOSE
POSITION GND
RECORDER
MAX REVERSE SENSITIVITY
GATE SPEED
OBD PORT MOTOR OVERLOAD
BLACK BOX GATE OPEN
NO LIMIT SWITCH /
STATUS COM
CLAMP SLIPPING CLAMP SLIP
CLOSE
LIMIT BATTERY
SWITCH
IN USE
ON-LINE
MOTOR
ON-LINE POWER
PRIMARY SEC
GATE GATE
31