Table of Contents
Advertisement
Installation Guide for
MAX 1500 PRO/2200 PRO/f18 PRO
Slide Gate Operators
MATRIX III
CONFORMS TO UL STD 325
CONFORMS TO UL STD 325
MAX 1500 PRO/2200 PRO UL CLASS - I, II, III, IV
SAFETY SENSORS REQUIRED
MAX F18 PRO UL CLASS - III, IV ONLY
CERTIFIED TO CAN/CSA STD
C22.2 NO. 247
Residential/Commercial
Brushless DC Slide Gate Operators
Made in USA
4009963
www.max.us.com
Version 7d
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for Maximum Controls MAX 1500 PRO
Summary of Contents for Maximum Controls MAX 1500 PRO
- Page 1 Slide Gate Operators MATRIX III CONFORMS TO UL STD 325 CONFORMS TO UL STD 325 MAX 1500 PRO/2200 PRO UL CLASS - I, II, III, IV SAFETY SENSORS REQUIRED MAX F18 PRO UL CLASS - III, IV ONLY CERTIFIED TO CAN/CSA STD C22.2 NO.
- Page 2 Exception : Les commandes d’accès d’urgence accessibles au personnel autorisé seulement (p. ex. pompier, policier, SMU) peuvent être placées à tout endroit dans le champ de visibilité de la barrière. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d Safety - 1...
- Page 3 7) One or more contact sensors shall be located at the bottom edge of a vertical barrier (arm). 7) Au moins un capteur de contact doit être situé sur le bord inférieur d’une barrière verticale (bras). UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d Safety-2...
- Page 4 7. La voie d’accès est réservée aux véhicules seulement. Les piétons doivent utiliser une voie d’accès différente. 8. SAVE THESE INSTRUCTIONS. 8. CONSERVEZ CES INSTRUCTIONS. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d Safety - 3...
- Page 5 B2 - Provision for connection of a contact sensor (edge device or the equivalent). B1 and B2 means of entrapment protection must be MONITORED. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d Safety - 4...
-
Page 6: Intended Use Of Slide Gate Operator
Entrapment sensors must be installed where entrapment or pinch point exist. A minimum of TWO entrapment protection sensors MUST be installed, ONE in EACH direction of gate travel or operator will NOT function. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d Safety-5a... - Page 7 UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d Safety-5b...
-
Page 8: Table Of Contents
- UL 325 Type A Inherent (ERD sensor) - Inputs for NORMALLY CLOSED (N.C.) and 10K Type 19” 14 1/2” UL 325 Type B1 (photocell) and Type B2 (sensing edge) UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 9: Step-By-Step Installation
Concrete Pad Concrete Depth Note: The heavier the gate, the deeper the concrete pad should be. At least two feet recommended for heavier gate. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 10: Connect Chain To Gate (Standard)
Chain chain. 7.5” 7.5” position Bracket 13.5” 13.5” Concrete Pad 6” DO NOT mount chain Operator in Front Position (Standard) bracket too high on gate. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 11: Rear Mounting Position (Alternate)
Concrete Pad Concrete Depth Note: The heavier the gate, the deeper the concrete pad should be. At least two feet recommended for heavier gate. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 12: Connect Chain To Gate (Rear Pos)
Approx.1.5” and existing chain exit slot. 16.5” Make sure cuts are plumb with existing Remove chain exit slot. Existing chain exit slot. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 13: Ac Input Power
O f f T u r CYCLE OPERATOR! LEDs should light up on operator. Battery power automatically turns ON. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 14: Ground Operator
OPEN ONLY PRIMARY SECONDARY 24VDC OUTPUT PRIMARY ENTRAP CLS ONLY OPENING CLOSING OPEN/CLS IMPORTANT: 12VDC OUTPUT 12VDC OUT Set EACH LINK PRIMARY/ SECONDARY LINK BEFORE NOTE: UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 15: Entrapment Protection Wiring
UL 325 2018 Standard MUST ONE in EACH CLOSING Direction Photocell Inside Entrapment Area IMPORTANT: MUST Beam Height: OPENING Direction Photocell Entrapment Area IMPORTANT: MUST UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... - Page 16 CLS ONLY OPEN/CLS Closing Direction Sensor is bad 12VDC OUT Opening Closing MOTION CONTROL 3. Press STOP Direction Direction NOTE: STOP 10K Sensing Edges STOP UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d...
-
Page 17: Program Virtual Limit Sensors
You should now see the PROGRAM LED flash simultaneously with PRIMARY/ SECONDARY LINK the GATE OPEN LED. Now press the PROGRAM BUTTON (the OPEN limit(s) are now learned.) UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 18: Learn Gate Positions
If alarm sounds while adjusting ERD, Position 16 results in gate exerting press STOP BUTTON to shut-off alarm. CAUTION: STOP OPEN CLOSE MAXIMUM force before reversing direction. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 19: Loops & Loop Detectors
CLS ONLY OPENING CLOSING OPEN/CLS 12VDC OUTPUT 12VDC OUT LINK Learned Turned ON - OPENING PRIMARY/ “ GATE SECONDARY safety loop LINK SPEED” preventing UNAUTHORIZED entry. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 20: Wiring Opening Device Options
NOTE: If STOP button is not pressed within 5 min., learn mode terminates. STOP If no “LEARNED” sensors are detected then factory default setting is restored (Inputs will NOT be Monitored). OPEN CLOSE UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 21: Additional Features
Dual Gate Operators NOTE: (alarm for slider only) Primary ONLY NO-connect NC-disconnect CLOSED OPEN Wired Wireless Normal operation Anti-tailgate ONLY MUST be OFF DO NOT UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 22: Gate Shut-Off Switch
KEY availability. Slide door open Turn and HOLD key either way and insert key. for reversible gate directions. Jog Switch UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 23: Gate Tamper Feature
24VDC OUTPUT ENTRAP CLS ONLY OPENING CLOSING OPEN/CLS 12VDC OUTPUT 12VDC OUT LINK MUST PRIMARY/ SECONDARY LINK GATE TAMPER Gate Tamper LEDs Alarm Reset Button UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 24: Partial Open Programming
The alarm reset button MUST be pressed to turn OFF the alarm and reset the operator. If GATE TAMPER relay is connected to an existing building alarm system, then they will get a triggering of their alarm system and should be notified of the situation. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 25: Dual Gate Operators Wiring
Primary RS-485 (-) to Secondary RS-485 (-) Primary RS-485 GND to Secondary RS-485 GND Secondary Operator Primary Operator Alarm Shut-OFF MOTION CONTROL NOTE: “STOP” EITHER STOP OPEN CLOSE UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 26: Gate Disable Feature
SECON LINK LINK When FIRE DEPT/MAX OPEN gets activated: GATE TAMPER GATE DISABLE When RADIO Input gets activated: GATE TAMPER after 3 min GATE DISABLE UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 27: Troubleshooting
IMPORTANT: OPEN/CLS 12VDC OUT NOT be OPEN ONLY MONITORED Sensor is bad CLS ONLY OPEN/CLS 12VDC OUT MOTION CONTROL 3. Press STOP NOTE: STOP STOP UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 28: Gate Cycling Troubleshooting
Gate does not learn new • Use jog Right and jog Left buttons to learn new positions instead of using open or close buttons. magnet positions. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 29: Matrix Iii Led Troubleshooting
“PROGRAM” LED is FLASHING • Program button has been pressed and programming mode is active. Press button again to leave programming mode. Table continued on next page UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... - Page 30 Check if OPEN and CLOSE Limits have been learned. Refer to “Learn Gate Positions” (see slowly. • ONLY Maximum settings will turn LEDs ON. All other settings, LEDs remain OFF. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d...
- Page 31 NOT be MONITORED. it will NOT be MONITORED. For 10K Resistor E3K Photocell wiring see next page For 10K Resistor E3K Photocell wiring see next page UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d...
-
Page 32: Omron E3K-R10K4 Ul325 2016
DO NOT use 10K Resistor included with photocell. DO NOT use 10K Resistor included with photocell. DO NOT use 10K Resistor included with photocell. DO NOT use 10K Resistor included with photocell. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 33: Omron E3K-R10K4 Ul325 2018
NOTE: To meet the UL 325 2018 standard, OPEN/CLS 12VDC OUT Type B1 Non-Contact sensor entrapment 12VDC OUT protection device MUST be MONITORED Polarity does NOT matter by the gate operator. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 34: Emx Wel-200 Wiring
OPEN ONLY PHOTO CLS OPEN/CLS 12VDC OUT WIRE TO ‘NO’ OF RELAY OPEN OPEN ONLY CLS ONLY WIRE TO ‘NO’ OF RELAY CLOSE OPEN/CLS 12VDC OUT UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 35: Wel-200 Programming
If the channel does not exhibit this behavior, double check the edge wiring/termination and transmitter batteries. FACTORY RESET Testing Power down receiver. Hold channels 1 and 4 down simultaneously while powering receiver back up. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 36: Emx-Ret Wiring
12VDC OUT function 12VDC OUT using VRX Polarity does NOT matter power input, OPEN ONLY connect CLS ONLY power to VTX OPEN/CLS input instead. 12VDC OUT UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 37: Emx Irb-Mon Single Gate Wiring
OPEN/CLS 12VDC OUT NOTE: To meet the UL 325 2018 standard, Type B1 Non-Contact sensor entrapment protection device MUST be MONITORED by the gate operator. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 38: Emx Irb-Mon Dual Gate Wiring
NOTE: To meet the UL 325 2018 standard, Type B1 Non-Contact sensor Matrix III or they will NOT be MONITORED. entrapment protection device MUST be MONITORED by the gate operator. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 39: Miller Rband Monitored Wireless
3. When the chirping stops, release the program button. Wait ~10 seconds and you will hear 2 beeps. The receiver is now ready to be reprogrammed. UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 40: Wiring Overview
Card Reader Keypad Reset Button Stop Dry Contact Safety Opening Device Key Switch Manual Release Secondary Operator RS-485 Communication see page 17 Manually Releases Slide Gate UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 41: Optional Magnet Limit Sensors
Use JOG Left/Right Buttons for installation 1. Install GRAY sensor on OPEN BLACK sensor on CLOSE CLOSE LEFT RIGHT OPEN HOLD JOG LEFT or JOG RIGHT UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... -
Page 42: Solar Pack Quick Installation Guide
24V, 35A / Hr 2 x 12V Batteries YUASA Fuse 1 Year Warranty ON/OFF Switch Power Cable UL325 Compliant UL1741 Power IN/Solar IN Compliant on MATRIX III UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d... - Page 43 Maximum Controls LLC. • 949.699.0220 • 10530 Lawson River Ave, Fountain Valley, CA 92708 Rev April25 for standard installation and setup of limit switches DO NOT TURN ON THE SOLAR MODE SWITCH UNTIL INSTALLATION IS COMPLETED UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d...
- Page 44 Solar pack quick installation guide PRO SERIES Solar Application Guide/Wiring Turn SOLAR MODE ON www.max.us.com Operator will go into low power mode 30 seconds NOTE: Operator will go into SOLAR MODE BATTERY MATRIX III after gate stops moving and loop detectors are not BATTERY VOLTAGE low power mode 90 seconds INPUT...
- Page 45 #NUM ! #NUM! #NUM! #NUM! 120W * Solar Panel NOTE: Must Use 24V Solar Panel #NUM! 85 W #NUM! #NUM! #NUM! 120 W 200 W UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d...
- Page 46 NOTES UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d...
- Page 47 NOTES UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7d...
- Page 48 MATRIX III www.max.us.com CONFORMS TO UL STD 325 MAX 1500 PRO/2200 PRO UL CLASS - I, II, III, IV SAFETY SENSORS REQUIRED MAX F18 PRO UL CLASS - III, IV ONLY CERTIFIED TO CAN/CSA STD C22.2 NO. 247 Residential/Commercial Brushless DC Slide Gate Operators...
Need help?
Do you have a question about the MAX 1500 PRO and is the answer not in the manual?
Questions and answers